Knick Protos LDO 3400-170 Скачать руководство пользователя страница 31

Страница: 31 / 64

Messages

Setting the Message Parameters

Messages

Note:

Function check (HOLD) mode active (Setting: BASE module)

Menu Display

Messages

All parameters determined by the

measuring module can generate

messages.

Variable limits:

For the “failure” and “warning” mes-

sages you can define upper and lower

limits for message generation.

Messages (Administrator)

20.1 °C

Return

83.4 %Air

Messages Partial pressure (Administrator)

20.1 °C

Abort

Monitoring

83.4 %Air

Variable limits

Off

Messages Partial pressure

Messages Saturation %O2

Messages Saturation %Air

Messages Concentration

Messages (Administrator)

20.1 °C

83.4 %Air

Warning Limit Hi

Monitoring

Failure Limit Lo

Failure Limit Hi

Warning Limit Lo

0400 mbar

Variable limits

0450 mbar

0100 mbar

0050 mbar

Abort

Message list

22.3 °C

Fail O2 partial pressure

83.4 %Air

Fail O2 concentration

Abort

Diagnostics menu

When the “Maintenance” or “Failure”

icons are blinking in the display, you

should access the Diagnostics menu.

The messages are displayed in the

“Message list”.

Failure (Failure limit HiHi/LoLo)
Maintenance (Warning limit Hi/Lo)

Message icons:

he displa

y ma

y v

y depending on the devic

e v

ersion.

Содержание Protos LDO 3400-170

































































Результаты поиска

Содержание Protos LDO 3400-170

Отзывы:

Похожие инструкции для Protos LDO 3400-170

Бренды по названию

Популярные бренды

Knick Protos LDO 3400-170, Руководство пользователя

Результаты поиска

Содержание Protos LDO 3400-170

Отзывы:

Похожие инструкции для Protos LDO 3400-170

Бренды по названию

Популярные бренды