Knick Protos II 4400 Скачать руководство пользователя

Страница: 76 / 112

Menu Display

Diagnostic functions

Opening the diagnostics menu

From the measuring mode:

Press menu key to select menu.

Select diagnostics using arrow keys,

confirm by pressing enter.

The “Diagnostics” menu gives an

overview of all functions available.

Functions which have been set as

“Favorite” can be directly accessed

from the measuring mode.

Diagnostic Functions

General status information of the measuring system

Select menu: Diagnostics - Message list

Message list

Shows the currently activated warning

or failure messages in plain text.

Menu selection

Return to meas

7.00 pH

25.6°C

Select:

[enter]

Lingua

Diagnostics

Return

23.7 °C

Set favorite

7.00 pH

Logbook

Message list

Device description

Module FRONT

Message list

Return

25.6°C

7.00 pH

Warn

Module BASE

8 messg.

Meas point description

Warn Temp alarm HI

Saturation %Air Alarm HI
Fail Wrong ISM sensor

Warn Tolerance band

Warn Zero range

D062

P018

D013
P210

P030

Sensocheck

P092

Number of messages
When there are more than 7 messages,
a vertical scrollbar appears.
Scroll with the up/down arrow keys.

Module identifier
Specifies the module that has generated the
message.

Message identifier
See message list for description.

he displa

y ma

y v

y depending on the devic

e v

ersion.

Содержание Protos II 4400

















































































































Результаты поиска

Содержание Protos II 4400

Отзывы:

Похожие инструкции для Protos II 4400

Бренды по названию

Популярные бренды

Knick Protos II 4400, Руководство пользователя

Результаты поиска

Содержание Protos II 4400

Отзывы:

Похожие инструкции для Protos II 4400

Бренды по названию

Популярные бренды