Knick Protos II 4400 Скачать руководство пользователя

Страница: 70 / 112

Menu Display

Module diagnostics /

Sensor monitor

Opening the diagnostics menu

From the measuring mode:

Press menu key to select menu.

Select diagnostics using arrow keys,

confirm by pressing enter.

Then select "Module PH".

The Diagnostics menu gives an over-

view of all diagnostics functions avail-

able. Messages set as “Favorite” can be

called up directly from the measuring

mode using a softkey.

To configure:

Parameter setting / System control /

Function control matrix.

Module diagnostics

Internal function test (without Fig.).
Sensor monitor

Shows the values currently measured

by the sensor. Important function for

diagnostics and validation!

(cf Maintenance)

Menu selection

Return to meas

22.3 °C

Select:

[enter]

Lingua

Module PH 3400-035

22.3 °C

Return

Cal record

Sensor monitor

7.00 pH

Sensor network diagram
Statistics

Set favorite

Module diagnostics

Sensor monitor

Return

pH input

22.3 °C

ORP input

7.00 pH

Temperature
Impedance glass (25°C)
Impedance ref (25°C)

43 mV

-109 mV

25.6 °C

322.8 MΩ
80.0 kΩ

Diagnostic Functions

Menu selection: Diagnostics / Module PH ...

RTD

1.100 kΩ

he displa

y ma

y v

y depending on the devic

e v

ersion.

Содержание Protos II 4400

















































































































Результаты поиска

Содержание Protos II 4400

Отзывы:

Похожие инструкции для Protos II 4400

Бренды по названию

Популярные бренды

Knick Protos II 4400, Руководство пользователя

Результаты поиска

Содержание Protos II 4400

Отзывы:

Похожие инструкции для Protos II 4400

Бренды по названию

Популярные бренды