Knick Protos II 4400 Скачать руководство пользователя

Страница: 69 / 112

Menu Display

Diagnostic functions

Device description

Select module using arrow keys:

Provides information about all

modules installed: Function, serial

number, hardware and firmware

version and device options.

FRONT module

The module contains the display

and keypad control.

Test possibilities:

• Module diagnostics

• Display test

• Keypad test

BASE module

The module generates the standard

output signals.

Test possibilities:

• Module diagnostics

• Input/output status

Example:

Module BASE, input/output status.

Device description

Return

22.7 °C

6.53 pH

Input for pH, ORP and °C

Module PH 3400-035

Hardware: 1, Software: 3.0

Serial number 0002283

BASE

Module

FRONT

Module FRONT

Return

22.7 °C

6.53 pH

Display test

Keypad test

Module diagnostics

Module BASE

Return

22.7 °C

6.53 pH

Input/output status

Set favorite

Module diagnostics

Input/output status

Return

22.7 °C

6.53 pH

Current load I1

Current load I2

Contact

Input OK1

Input OK2

Inactive

Diagnostic Functions

Device description, FRONT module, BASE module

Set favorite

he displa

y ma

y v

y depending on the devic

e v

ersion.

Содержание Protos II 4400

















































































































Результаты поиска

Содержание Protos II 4400

Отзывы:

Похожие инструкции для Protos II 4400

Бренды по названию

Популярные бренды

Knick Protos II 4400, Руководство пользователя

Результаты поиска

Содержание Protos II 4400

Отзывы:

Похожие инструкции для Protos II 4400

Бренды по названию

Популярные бренды