Knick Protos II 4400 Скачать руководство пользователя

Страница: 32 / 112

Calibration with manual entry of buffer values

Calibration with manual entry of buffer values is performed with one, two or

three buffer solutions.

Protos displays the measured temperature.

You must then enter the temperature-corrected buffer values. To do so, refer to

the buffer table (e.g. on the bottle) and enter the buffer value belonging to the

displayed temperature.

Intermediate values must be interpolated.

All calibration data is converted using a reference temperature of 25 °C/77 °F.
During calibration the module is in function check (HOLD) mode.

Current outputs and relay contacts of the module behave as configured

(Module BASE).

NOTICE!

Only ever use fresh, undiluted buffer solutions!

Menu Display

Manual entry

Manual entry

Return

Cal medium: Buffer solution

When changing sensors perform

First cal for statistics!

Cal temp

25.6 °C

7.00 pH

+025.6 °C

Proceed

First buffer solution

+04.00 pH

Manual entry

Return

Dip sensor in 1st buffer!

then ‘Start’ calibration.

25.6 °C

7.00 pH

Start

Remove and rinse the electrode

(

NOTICE!

Electrostatic hazard.

Do not rub.),

then immerse it in the first buffer

solution.

Start by pressing softkey or enter.

Select: Manual entry

Select: Sensor replacement
Display: calibration temp

Enter first buffer value

Proceed by pressing softkey or enter

Calibration / Adjustment

Calibration with manual entry of buffer values

Sensor replacement

he displa

y ma

y v

y depending on the devic

e v

ersion.

Содержание Protos II 4400

















































































































Результаты поиска

Содержание Protos II 4400

Отзывы:

Похожие инструкции для Protos II 4400

Бренды по названию

Популярные бренды

Knick Protos II 4400, Руководство пользователя

Результаты поиска

Содержание Protos II 4400

Отзывы:

Похожие инструкции для Protos II 4400

Бренды по названию

Популярные бренды