Knick Protos II 4400 Скачать руководство пользователя

Страница: 27 / 112

For automatic cal temp detection, the Protos

measures the temperature of the buffer solution

with a temperature probe (Pt 100/ Pt 1000/

NTC 30 kΩ/NTC 8.55 kΩ). If you work with

automatic temperature compensation during

calibration, a temperature probe connected to

the temperature input of the Protos must be in

the buffer solution! Otherwise, you must select

manual entry of calibration temperature. When ”Cal temp automatic” is set,

”Measured cal temp” appears in the menu.

Temperature compensation during calibration

Calibration / Adjustment

Temperature compensation

Calimatic

Return

Cal medium: Buffer solution

Knick 2.00 4.01 7.00 9.21

When changing sensors perform

First cal for statistics!

Measured cal temp

25.6 °C

7.00 pH

+025.6 °C

Proceed

Sensor replacement

Automatic temperature compensation

There are two important reasons for determining the temperature of the buffer

solution:

The slope of the pH electrode is temperature-dependent. Therefore the

measured voltage must be corrected by the temperature influence.

The pH value of the buffer solution is temperature-dependent. For calibration,

the buffer solution temperature must therefore be known in order to choose

the actual pH value from the buffer table.

During parameter setting you define whether cal temperature is measured

automatically or must be entered manually:

Manual temperature compensation

The temperature of the buffer solution must be

entered manually in the Parameter setting menu

at "Parameter setting / <PH module> / Sensor

data / Temp detection / Cal temp --> manual".

Temperature measurement is performed using a

glass thermometer, for example.

Temp detection (Administrator)

Temp probe

Measuring temp

Cal temp

25.6 °C

7.00 pH

+025.6 °C

Manual

Auto

Pt 1000

Manual

Auto

he displa

y ma

y v

y depending on the devic

e v

ersion.

Содержание Protos II 4400

















































































































Результаты поиска

Содержание Protos II 4400

Отзывы:

Похожие инструкции для Protos II 4400

Бренды по названию

Популярные бренды

Knick Protos II 4400, Руководство пользователя

Результаты поиска

Содержание Protos II 4400

Отзывы:

Похожие инструкции для Protos II 4400

Бренды по названию

Популярные бренды