Knick Protos II 4400 Скачать руководство пользователя

Страница: 17 / 112

Installing the Module

CAUTION! Electrostatic discharge (ESD).

The modules' signal inputs are sensitive to electrostatic discharge.

Take measures to protect against ESD before inserting the module and wiring

the inputs.

Note: Strip the insulation from the wires using a suitable tool to prevent dam-

age.

1) Switch off the power supply to the device.

2) Open the device (loosen the 4 screws on the front).

3) Plug the module into the slot (D-SUB connector),

see figure.

4) Tighten the module's fastening screws.

5) Open the ESD shield (covering terminals 2 and 8).

6) Connect the sensor and separate temperature probe if necessary, see

"Wiring Examples".

Note: To avoid interferences, the cable shielding must be completely

covered by the ESD shield.

7) Fit the ESD shield back into place (covering terminals 2 and 8).

8) Check whether all connections are correctly wired.

9) Close the device by tightening the screws on the front.

10) Switch on the power supply.

CAUTION! Incorrect measurement results.

Incorrect parameter setting, calibration or adjustment may result in incorrect

measurements being recorded. Protos must therefore be commissioned by a

system specialist, all its parameters must be set, and it must be fully adjusted.

ESD shield

Содержание Protos II 4400

















































































































Результаты поиска

Содержание Protos II 4400

Отзывы:

Похожие инструкции для Protos II 4400

Бренды по названию

Популярные бренды

Knick Protos II 4400, Руководство пользователя

Результаты поиска

Содержание Protos II 4400

Отзывы:

Похожие инструкции для Protos II 4400

Бренды по названию

Популярные бренды