Knick Portavo 908 MULTI Скачать руководство пользователя страница 36

Страница: 36 / 76

Oxy Cond

ORP

Measuring

Once you have completed all preparations, you can start with the actual
measurement.

1) Connect the desired sensor to the meter. Some sensors require a special

preparation. Please proceed according to the operating instructions for the
sensor.

2) Switch the meter on using the on/off or meas key.

3) Depending on the measurement method and the sensor used, immerse the

sensing part of the sensor in the medium to be measured.

4) Watch the display and wait for the reading to stabilize.

Note: Measurement can also be controlled via the Paraly SW 112 software.

Toggling the Measured Value Display

During measurement, you can toggle between display of
primary / secondary measured values and clock by pressing meas.

Adjusting the Temperature

When you connect a sensor without temperature detector, you can manually adjust
the temperature for measurement or calibration:
1) Press meas to access measuring mode. The adjusted temperature will be

displayed.

2) Set the desired temperature value using the





arrow. Holding the key

depressed changes the temperature value at high speed.

Содержание Portavo 908 MULTI













































































Результаты поиска

Содержание Portavo 908 MULTI

Отзывы:

Похожие инструкции для Portavo 908 MULTI

Бренды по названию

Популярные бренды

Knick Portavo 908 MULTI, Руководство пользователя

Результаты поиска

Содержание Portavo 908 MULTI

Отзывы:

Похожие инструкции для Portavo 908 MULTI

Бренды по названию

Популярные бренды