Knick A405B Скачать руководство пользователя

Страница: 45 / 108

Configuring the Current Output

HOLD active

Output current
[mA]

Output signal for HOLD
FIX setting = 21.0 mA

Output signal for HOLD
LAST setting

Output signal during HOLD:

Menu item

Action

Choices

Output current during
error message

The output current can be set to
22 mA in the case of error mes-
sages or error messages.
Select ON or OFF using



keys.
Confirm by pressing enter

OFF / ON

Output current during
Sensoface messages

The output current can be set to
22 mA in the case of Sensoface
messages.
Select ON or OFF using



keys.
Confirm by pressing enter

OFF / ON

Output current during
HOLD

LAST: During HOLD the last
measured value is maintained at
the output.
FIX: During HOLD a value (to be
entered) is maintained at the
output.
Select using



Press enter to confirm.

LAST/FIX

Output current for HOLD
FIX

Only with FIX selected:
Enter current which is to flow at
the output during HOLD
Enter value using





keys.

Press enter to confirm.

00.00...22.00 mA
(21.00 mA)

Содержание A405B













































































































Результаты поиска

Содержание A405B

Отзывы:

Похожие инструкции для A405B

Бренды по названию

Популярные бренды

Knick A405B, Руководство пользователя

Результаты поиска

Содержание A405B

Отзывы:

Похожие инструкции для A405B

Бренды по названию

Популярные бренды