background image

Transportation 

 

Diaphragm Vacuum Pumps N86.16 

12 

Translation of original Operating and Installation Instructions, english, KNF121260-121531 04/20 

6.  Transportation 

 

 

CAUTION 

 Personal injury and/or damage to property because 

of false or improper transportation of the pump 

 

Due to false or improper transportation the pump can 
fall down, become damaged and injure people. 

 

  If necessary, use suitable aids (eyebolt, harness, 

lifting device, etc.). 

  If necessary, wear proper personal protective 

equipment (e.g. safety gloves, safety shoes). 

 

 

CAUTION 

 Danger of injury due to sharp edges on the package 

 

When handling or opening the package there is the 
possibility of injury by cutting at sharp edges. 

 

  If necessary, wear proper personal protective 

equipment (e.g. safety gloves). 

 

  Carry the pump in the original packaging up to its place of in-

stallation. 

  Retain the original packaging of the pump (e.g. for later stor-

age). 

  Check the pump for transport damages after receipt. 

  Document occurred transport damages in writing and with pic-

tures. 

  If necessary, remove the transport safety devices before com-

missioning the pump. 

 

Parameter 

Parameter 

Value 

Storage temperature 

+ 5°C to + 40°C 

Transport temperature 

- 10°C to + 60°C 

Permiss. humidity (non-con-

densing) 

30% to 85% 

 

Tab. 8 

 

Содержание N86.16 Series





























Отзывы: