manualshive.com logo in svg

KNECHT W 200 II, Руководство по эксплуатации

Поделиться
Скачать
KNECHT W 200 II Скачать руководство пользователя страница 18

19

3. Description 

3.4.1  Switching the grinding machine on / off

The main switch is located at the front of the 
control panel.

Turning the main switch from “0” to “I” switches 
on the grinding machine.

Turning the main switch from “I” to “0” switches 
off the grinding machine.

3.4.2  Control panel

The machine is operated via the control panel of 
the PLC control. 

The mechanical components are operated using 
the control buttons and switches.

1 

 “Grinding wheel On / Off” button: Switch 
grinding  wheel  on / off 

2 

 “Rotary table On / Off” button: Switch rota-
ry table movement on / off

3 

 “Coolant On / Off” button: Switch coolant 
pump  on / off

4 

 “Control ON” button Activate PLC control

5 

 “Drives On / Off” button: Switch drives for 
grinding wheel, rotary table, coolant pump 
and suction unit on / off

6 

“Emergency stop” button

Figure 3-4

 Main switch

Figure 3-5

 Control panel

1

2

3

5

4

6

Содержание W 200 II









































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды