manualshive.com logo in svg

KNECHT W 200 II, Руководство по эксплуатации

Поделиться
Скачать
KNECHT W 200 II Скачать руководство пользователя страница 13

14

After completing maintenance work and fault rectification, install all safety devices and verify that 
they are fully functional.

2.4.10  Structural modifications to the grinding machine

Modifications, retrofitting or rebuilds of the grinding machine are not allowed without the per-
mission of the manufacturer. This also applies for installation and configuring the safety devices.

Any conversion work requires the written permission from KNECHT Maschinenbau GmbH.

Immediately replace any machine parts that are not in a serviceable state.

Use only original replacement and wear parts. When using external parts, it cannot be guaranteed 
that they are constructed and manufactured to be suitable and safe.

2.4.11  Cleaning the machine

Handle any cleaning agents and materials used properly and dispose of them in an environmen-
tally-friendly manner.

Dispose of parts subject to wear and replacement parts in a safe and environmentally-friendly 
manner.

2.4.12  Oils and greases

When using lubricants and grease, follow the safety provisions applicable to the product. Comply 
with the special regulations for the foodstuffs sector.

2.4.13  Relocation of the grinding machine

Disconnect the grinding machine from any external power, even if adjusting its position slightly. 
Before restarting the grinding machine, properly connect it to the power supply.

When loading or unloading, only use suspension devices and load suspension devices with suffi-
cient load-bearing capacity. Designate suitable lifting devices for the lifting process.

Ensure that no one, who is not certified for this work, is located where the machine is unloaded 
and installed.

Only lift the grinding machine correctly with a suspension device in accordance with the operating 
instructions (attachment points for load suspension devices, etc.). Use only a suitable transport 
vehicle with sufficient carrying capacity. Secure loads safely. Use suitable attachment points. When 
putting the machine into operation again, proceed only as instructed in the operating instructions.

2. Safety 

Содержание W 200 II









































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды