manualshive.com logo in svg

Knauer BlueShadow Series, Руководство пользователя

Поделиться
Скачать
Knauer BlueShadow Series Скачать руководство пользователя страница 32

33

Installation

The connections at the interfaces are detected automatically 
by the device.

The LAN connection and the RS-232 interface can be used for 
the valves. The remote control is often used when the devices 
are employed in an analytical system whose chromatography 
software does not support the driver software of the manufac-
turer.

Use the 

Remote

 terminal strip to connect the valve with exter-

nal devices.

Use the LAN connection to connect the valve with external 
devices within a network.

Alternatively, connect the valve via the communication inter-
face RS-232 port to a computer.

Caution!

Electrostatic discharge can damage the electron-
ics of the valve!

Never touch the electric contacts of the 

Remote 

terminal strip!

Remote

 terminal strip

For receiving start, control and error signals from external 
devices

For sending start, control and error signals to external devices

Fig. 30

Terminal strip: 

Remote

GROUND

Start and error signals are started to the ground connection 
without a current flow.

A

Содержание BlueShadow Series




























































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды