manualshive.com logo in svg

KMS Simplekey 4, Руководство по установке

Поделиться
Скачать
KMS Simplekey 4 Скачать руководство пользователя страница 27

Key Management Systems Ltd

   

27

 | 

P a g e

 

Maximum cable runs 

Total KMS BUS 700 metres, includes BUS reader run. 

Reader Interface Mk1 (designated by UDN 050) to reader 50 metres. 

Reader Interface Mk2 (designated by UDN 052) to reader 100 metres. 

 

KMS BUS  

 

Cat5, Cat5e or Cat6 network cable of known brand and 
specification. 150ohm per 1000 metres minimum.  Due to the 
large variety of twisted pair data transmission cables 
manufactured, KMS are unable to recommend or endorse any 
brand. 

Reader Interface to Reader 

6 or 8 core Alarm multi-stranded cable, CW1308 (copper core) 

Lock Controller to Lock 

Twin 1mm

²

 copper flex assuming locks up to 1 Amp, installer 

to calculate for larger loads / longer runs. 

RTE to Lock Controller 

Alarm cable, CW1308, Cat5 

Other General INPUTS 

Alarm cable, CW1308, Cat5 

High Gain GPRS Antenna 

KMS provide Antennas in 5, 10, 15 and 20 metre lengths, all of 
which must not be cut and re-terminated due to tuning of 
antenna. Further information later in this guide. 

 

 

Содержание Simplekey 4





















































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды