KMC Controls KMD-5210 Скачать руководство пользователя страница 22 | Manualshive

Страница: 22 / 38

background image

KMC Controls

Revision E

Installation

Connecting Power

22

Caution

D

o not

crimp the cable in a tight fold. This may result in separation of cable

strands and result in unreliable operation of the module.

4. Connect input and output devices to the modules. Refer to the manuals

supplied with the KMD-5220 input module and the KMD-5220 output
module for details.

Connecting Power

Each KMD-5210 LAN Controller requires a KMD–5563 power supply for
operating power. Mount the power supply in a convenient location near the
KMD-5210 and route the supply cable to the controller.

The controller will automatically power on when the power connection is
complete. The controller does not use an power switch. See

Applying power

for additional information.

Caution

Use only a KMC Controls power supply. Powering the controller with an
improper supply may result in damage to the controller.

«
...
20
21
22
23
24
...
»

Содержание KMD-5210







































Отзывы:

Нет отзывов

Похожие инструкции для KMD-5210

Бренд: ABB Страницы: 138

Бренд: ABB Страницы: 116

Relion 615 series

Бренд: ABB Страницы: 136

Evolution Series E9000

Бренд: GE Страницы: 44

PACSystems RX7i

Бренд: GE Страницы: 469

GuardSwitch 300 Series

Бренд: GE Страницы: 2

GuardSwitch 300 Series

Бренд: GE Страницы: 2

Masoneilan VariPak 28001

Бренд: GE Страницы: 24

SolarCell Remote

Бренд: Samsung Страницы: 2

Бренд: Samsung Страницы: 20

Бренд: Dantherm Страницы: 96

Бренд: Access Страницы: 12

Бренд: Baccara Страницы: 16

Бренд: BABYSTYLE Страницы: 8

Бренд: BABYSTYLE Страницы: 32

Бренд: Gardena Страницы: 18

VLT Micro Drive FC 51 Series

Бренд: Danfoss Страницы: 23

Бренд: YOKOGAWA Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды