background image

CSC-3000 Series Pneumatic VAV Reset Volume Controllers 

    9 

Applications Guide, Rev G

Competitor Cross-Reference to KMC Universal CSC-3000 Series

KMC 

Controls

Invensys/Robertshaw/

Barber-Colman

TAC/Staefa/UPC

Honeywell

Johnson 

Controls 

Titus

CSC-3011

All Models of:

R77 and R78 Series

PPR-9100 Series

HYUR-2700 Series

VCV2100 Series (all Models)
VCV2200 Series (all Models)

VCV2500-101*
VCV2500-201*
VCV2500-301*
VCV2500-401*

CP980C**

CP980D**

CP980E**
CP980F**

P-3800-1*
P-3800-2*

CSC-3002
CSC-3003

CSC-2000s***

CSC-3025

VCV2500-101 (on Trane VAV Units)
VCV2500-201 (on Trane VAV Units)
VCV2500-301 (on Trane VAV Units)
VCV2500-401 (on Trane VAV Units)

P-3800-1 (on 

Trane VAV Units)

P-3800-2 (on 

Trane VAV Units)

CSC-3004
CSC-3005

 NOTE: After replacing the controller, adjustments and calibration will be necessary.
 *On Trane terminal units, use CSC-3025 instead.
 **For Honeywell CSP980, the existing velocity pressure flow pickup needs to be replace with KMC SSS-1000 series.
 ***See KMC CSC Cross-Reference to Universal CSC-3000 Series chart above. All Titus CSC-2000 Series controllers are the same as KMC 
      CSC-2000 Series.

KMC CSC Cross-Reference to Universal CSC-3000 Series

“Universal” Replacement KMC Model

Older KMC Model

CSC-3011

CSC-1001
CSC-2001
CSC-2003
CSC-2007

CSC-2011  (Discontinued )

CSC-2013  (Discontinued)

CSC-3014  (Discontinued)*

CSC-3017**

CSC-3501  (Discontinued)***

CSC-3021

CSC-2002
CSC-2004
CSC-2008

CSC-2012  (Discontinued)
CSC-2014  (Discontinued)

CSC-3016

CSC-2009

CSC-2015  (Discontinued)
CSC-2017  (Discontinued)

CSC-3505  (Discontinued)***

CSC-3026

CSC-2010
CSC-2016
CSC-2018

 NOTE: All Titus CSC-2000s are the same as KMC CSC-2000s.
 *The CSC-3014 also requires a thermostat replacement, with no limits at the thermostat.
 **The CSC-3017 is identical to the CSC-3011, but it does not come with mounting bracket or KMC logo.
 ***No direct replacement if the Linear feature is required.

Replacement Cross-References

NOTE:  For cross-references to 

competitive and 

OEM products

, see the 

KMC Master Cross-

Reference

.

Содержание CSC 3000 Series
















Отзывы: