background image

BAC-7401 Heat Pump Controller

Revision  E

13

SECTION  3

Operating the controller

This section provides a brief overview of the BAC-7401 and the 
BAC-7401C Direct Digital Controllers. Review this material before 
you attempt to install the controller.

Operation

Once configured, programmed and powered up, the controller requires very little 
user intervention. 

Controls and 
Indicators

The following topics describe the controls and indicators found on the controller. 
Additional information for automatic addressing functions are described in the 
guide 

MS/TP Automatic MAC Addressing Installation Instructions

 that is available 

from the KMC Controls web site.

Network disconnect switch

The network disconnect switch is located on the left side of the controller. Use this 
switch to enable or disable the MS/TP network connection. When the switch is ON 
the controller can communicate on the network; when it is OFF, the controller is 
isolated from the network.

Alternately, you may remove the isolation bulbs to isolate the controller from the 
network.

Illustration 3-1 Controls and indicators

 T4        R

TN       T3

  T2       R

TN      T1

1

Connected

Disconnected

Network 

disconnect 

switch

Isolation 

bulbs

Power 

jumper

Ready status LED

Com status LED

Restart button

Содержание BAC-7401



















Отзывы: