manualshive.com logo in svg

KMB SMP133, Руководство по эксплуатации

Поделиться
Скачать
KMB SMP133 Скачать руководство пользователя страница 58

SMY133-SMY134-SMP133 Operating Manual

7. Computer Controlled Operation

Monitoring the currently measured values and the instrument setup can be done not only on the 
instrument panel but also using a local or remote computer connected to the instrument via a 
communication link. Such an operation is more comfortable, and it also allows you to use all the 
options of the instrument, such as adjusting the inputs/outputs or setup and the monitoring of courses 
recorded into the internal memory of the instrument, which it is not possible from the panel of the 
instrument.
Following chapters describe instrument communication links from the software point of view and 
embedded webserver only. The detailed description of ENVIS program can be found in the program 
manual.

7.1 Communication Links

7.1.1 Local Communication Link

Instruments can be equipped with a serial interface USB 2.0, on the front panel. Using this interface, 
adjusting the parameters of the instrument and the transmission of data into a portable computer can 
be accomplished. It requires to interconnect the instrument with the PC using the appropriate 
communication cable (connector type “Mini-B”,  see optional accessory list).
Considering the fact that the instruments can be also equipped with a remote communication link, the 
described communication link is called 

Local

.

7.1.2 Remote Communication Links

The instruments may be optionally equipped with the  remote communication link for operation of the 
instrument via a remote computer. Subsequently, this computer can execute a remote adjusting of the 
instrument and transmission of current or recorded data.
The type of interface can be either RS-485 or Ethernet. Appropriate connector is situated at the rear 
panel. It is supposed the cable for remote communication link to be provided by customer.
One or more instruments can be connected to the remote PC via this link. Each instrument must have 
an adjusted proper remote communication address and protocol. These specifications can be set 
manually or by the computer via a local communication link in ENVIS program.
The remote communication link is always isolated from the internal circuits of the instrument. 
Selected models can be equipped with the second communication link RS-485.

7.1.2.1 RS-485 Interface (COM)

Up to 32 instruments at a maximum distance of 1,200 metres can be connected to this interface. Used
signals : 

A+ 

, 

B-

 , 

G

 , and optionally 

A+2 

, 

B-2

 , 

G2

.

Each instrument must have a different communication address within the range of 1 to 253 preset 
during the installation.
A USB/485 level converter must be installed on the computer side. For suitable converters see 
optional accessory list.

In case of  two communication links they are insulated both from the instrument internal circuitry and 
mutually too, terminals No. 30 and 33 

are not connected internally !

58

Содержание SMP133





















































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды