background image

3-12

   

CHAPTER 3 Setup and Test

HydroChart 3500 Sonar System Operations and Maintenance Manual

P/N 11210087, Rev. 03

3.10.1 Static Position Offsets

It is necessary to first measure the static position offsets between the Sonar Head 
Unit, the position sensor and the motion reference unit, relative to some reference. 
These measurements will provide the necessary data for applying lever-arm 
corrections to the final bathymetric solution. SonarPro provides an interface to 
record these offsets in the Ship Geometry Setup dialog box such that they can be 
recorded along with the sonar data to provide real time correction during data 
acquisition. See the "SonarPro User Manual" for more information.

3.10.2 Latency Error

This test will provide a measurement of the latency error, or time, in the overall 
system, which manifests itself as a position error in the processed data. It is 
recommended that lines be run in the same direction and at different speeds over 
an area with a prominent bathymetric feature. This will offset any effects due to 
pitch bias. The greater the speed difference the more accurate the measurement. 
The latency can be derived by measuring the along-track displacement of depth 
measurements over the bottom feature.

3.10.3 Roll Bias Test

This test determines the athwartship alignment error between the transducer arrays 
and the motion reference unit as well as any additional roll axis bias error in the 
motion reference unit. The result is a roll correction which can be used during post 
processing operations. For the roll bias test you should choose a relatively flat area 
of the sea bottom and run at least two reciprocal lines 200–300 meters in length at 
equal speeds in both directions.

3.10.4 Pitch Bias Test

Pitch bias is similar to roll bias, except that pitch error lies in the along-ship’s 
fore-aft axis. This error occurs when the motion reference unit and the transducer 
arrays are not pitch-aligned; that is, they are not mounted on the same fore-aft axis. 
The resulting error changes the apparent location of a feature and is proportional to 
water depth. In addition, along-track displacement error increases as water depth 
increases. For the pitch bias test the survey vessel should run reciprocal lines on a 
sloped bottom, preferably on the order of 10–20 degrees, for 200–300 meters. It 
may be possible to use a channel feature instead of a long sloping bottom. Speed 
for the test should be equal for both lines.

Содержание HYDROCHART 3500























































































Отзывы: