Klein Marine Systems, Inc. HYDROCHART 3500 страница 16 Скачать руководство пользователя

Страница: 16 / 86

xvi

Appendix D: Bathy Systems Calibration Procedure.

Provides a

procedure on how to calibrate a bathy system to align the phase differences
among the bathy channels after replacing one or more components in the bathy
channel path.

Appendix E: Outline Drawings.

Provides outline drawings for reference

purposes only.

Note, Warning and Caution Notices

Where applicable, note, warning and caution notices are included throughout this
manual as follows:

Customer Service

KMS technical support can be contacted using any of the following means:

Mail

Klein Marine Systems, Inc.

11 Klein Drive

Salem, NH 03079

Email

[email protected]

Telephone

(603) 893-6131

Facsimile

(603) 893-8807

For more information about KMS and our products, please go to our Web site at

www.KleinMarineSystems.com

NOTE

Recommendations or general information that is particular to the

material being presented or a referral to another part of this manual or to
another manual.

WARNING

Identifies a potential hazard that could cause personal injury

or death to yourself or to others.

CAUTION

Identifies a potential hazard that could be damaging to

equipment or could result in the loss of data.

Содержание HYDROCHART 3500























































































Результаты поиска

Содержание HYDROCHART 3500

Отзывы:

Похожие инструкции для HYDROCHART 3500

Бренды по названию

Популярные бренды

Klein Marine Systems, Inc. HYDROCHART 3500, Руководство по эксплуатации и обслуживанию

Результаты поиска

Содержание HYDROCHART 3500

Отзывы:

Похожие инструкции для HYDROCHART 3500

Бренды по названию

Популярные бренды