background image

WSR

WSR

YFR

YFR

GFR

GSL

GSL

YSL

YSL

YSL

YSL

BSR

BSR

BSR

BSR

1.  Select a dry, level site and clear 

the ground of any sharp objects. 
Remove the tent from its carry 
bag, untie fabric ties and unroll 
the tent.

2.  Spread out the floor of the inner 

tent and peg out the four main 
corners. Ensure that the tent is 
pulled taut and square. Proceed 
to peg out the remaining pegging 
points. Unzip and open the doors 
to make erecting the tent easier. 
Pitch the tent so it is in line with 
the wind, never side on. 

3.  Open the pole bag and assemble 

the poles grouping them by 
colour. 

4.  Take the two YELLOW fibreglass 

roof poles and feed them through 
the pole sleeves to create an ‘X’ 
over the roof of the inner tent.

Key:
YFR = Yellow Fibreglass Roof
GFR = Green Fibreglass Roof
WSR = White Steel Roof

To make sure the tent stays in place, 
insert the pegs into the ground at a 
45° angle.

REVERSE THE PROCEDURE TO LOWER THE TENT

Falcon 6 Tent

Model No. KC072-701

Your tent includes: 
41 x pegs
9 x ropes
2 x YELLOW fibreglass roof poles (3850mm x 11mm)
1 x GREEN fibreglass roof pole (2170mm x 11mm)
2 x WHITE curved steel roof poles (2000mm x 19mm)
4 x BLACK steel roof poles (1580mm x 16mm)
4 x YELLOW steel leg poles (1950mm x 19mm)
2 x GREEN steel leg poles (1810mm x 19mm)
2 x black PORCH poles (1900mm x 16mm)
1 x black PORCH poles (2100mm x 16mm)

PITCHING INSTRUCTIONS

PACKING INSTRUCTIONS
Pack the poles and pegs into their bags, place into their separate 
frame bag. Evenly lay out the fly inside the tent inner (this is best done 
when the inner is still pitched) leaving all doors and windows open. 
Replace the provided knuckle covers to protect the tent inner. Fold the 
tent as shown below, forcing all of the air out the front door. Roll into 
the tent bag provided. 

Ensure the tent is completely dry and clean before storing away and 

store it in a dry environment.

5.  Take the GREEN fibreglass roof pole and feed it through the 

pole sleeve over the YELLOW poles. 

6.  Insert the two WHITE curved steel roof poles into the corner 

quad knuckles at the front and back of the tent. Note: Make 
sure metal pin locks into slot on knuckle, you may have to 
twist pole from side to side. Attach the speed-clips.

7.  Take the four BLACK steel roof poles 

and one at a time lock them into the quad 
knuckles on each side of the roof of the 
tent. Attach the speed-clips. 

8.  Once all the steel roof poles are inserted 

into the knuckles proceed to insert the 
YELLOW fibreglass roof poles into the corner quad knuckles. 
Attach the speed-clips.

9.  Take the four YELLOW steel leg poles 

and insert them into the remaining 
knuckle openings on the four corners. 
This will take 2 people to assemble. It is 
recommended to erect adjacent corners. 
Fit the bottom of each pole onto the 
corresponding pin at the base of the 
inner so that the tent now stands. Attach 
the speed-clips. 

10. Take the remaining two GREEN steel leg poles and insert 

into the centre knuckle. Fit the bottom of each pole onto the 
corresponding pin and attach the speed-clips. The inner tent 
is now pitched. 

11. Carefully pull the fly over the inner making sure the windows 

and doors line up. Attach the ties on the underside of the fly 
around the frame. This will secure the fly and help the tent 
to perform better in the wind. Once the fly is secure, zip the 
doors up and peg out the fly ensuring there is an adequate 
gap between the inner and the fly.

12. Finally, rope out the guy ropes and fine tune the fly so it 

remains taut and positioned correctly over the tent.

13. When pegging out the black PORCH poles, make sure the 

ropes are at a 45° angle to ensure adequate tension. When 
raining, remove the centre pole or adjust the pole height to allow 
water build-up to run off. Zip-out the gussets for added weather 
protection.

14. Please read the care instructions for more product information 

about your tent.

Filename: 4975_KC072-701_Falcon 6_Instr.pdf
Dimensions:    410mm W x 200mm H 
Colour: Black

BSR = Black Steel Roof
YSL = Yellow Steel Leg 
GSL = Green Steel Leg 

Insert the pin into the end of 
the steel ferrule.

Lay flat

Fold once

Fold twice

Roll

Fold again

Отзывы: