background image

INSTALLATION AND SERVICE MUST BE PERFORMED BY A QUALIFIED INSTALLER.

IMPORTANT: SAVE FOR LOCAL ELECTRICAL INSPECTOR'S USE.

READ AND SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE.

Clearances and Dimensions

1. Provide adequate clearances between the range and adjacent combustible surfaces.
2. Location—Check location where the range will be installed. Check for proper electrical supply, and the stability of the floor.
3. Dimensions that are shown must be used. Given dimensions provide minimum clearance. Contact surface must be solid

and level.

*30" MINIMUM CLEARANCE BETWEEN THE TOP OF THE COOKING SURFACE AND THE  BOTTOM OF AN UNPROTECTED WOOD OR METAL

CABINET; OR 24" MINIMUM WHEN BOTTOM OF WOOD OR METAL CABINET IS PROTECTED BY NOT LESS THAN 1/4" FLAME RETARDANT

MILLBOARD COVERED WITH NOT LESS THAN NO. 28 MSG SHEET STEEL, 0.015" STAINLESS STEEL, 0.024" ALUMINUM OR 0.020" COPPER.

0" CLEARANCE IS THE MINIMUM FOR THE REAR OF THE RANGE. FOLLOW ALL DIMENSION REQUIREMENTS PROVIDED ABOVE TO

PREVENT PROPERTY DAMAGE, POTENTIAL FIRE HAZARD, AND INCORRECT COUNTERTOP AND CABINET CUTS.

TO ELIMINATE THE RISK OF BURNS OR FIRE BY REACHING OVER HEATED SURFACE UNITS, CABINET STORAGE SPACE LOCATED

ABOVE THE SURFACE UNITS SHOULD BE AVOIDED. IF CABINET STORAGE IS TO BE PROVIDED, THE RISK CAN BE REDUCED BY

INSTALLING A RANGE HOOD THAT PROJECTS HORIZONTALLY A MINIMUM OF 5" BEYOND THE BOTTOM OF THE CABINETS.

p/n 316454912 rev A

 If the information in this manual is not followed

exactly, a fire or electrical shock may result causing property
damage, personal injury or death.

Important Notes to the Installer

Read all instructions contained in these installation instructions

before installing range.

Remove all packing material from the oven compartments

before connecting the gas & electrical supply to the range.

Observe all governing codes and ordinances.

Be sure to leave these instructions with the consumer.

Fig. 1

Fig. 2

Fig. 3

30"

Important Note to the Consumer

Keep these instructions with your owner's guide for future reference.

As when using any appliance generating heat, there are

certain safety precautions you should follow. These are listed

in the Use & Care Guide, read it carefully.

Be sure your range is installed and grounded properly by a

qualified installer or service technician.

Make sure the wall coverings around the range can withstand

the heat generated by the range.

To eliminate the need to reach over the surface elements,
cabinet storage space above the elements should be avoided.

IMPORTANT SAFETY INSTRUCTIONS

Serial plate is located on the lower right front frame of the appliance.

Alternate location may be under cooktop.

Serial Plate Locations:

INSTALLATION INSTRUCTIONS FOR FREESTANDING ELECTRIC RANGE

1

Español - Páginas 5-8

Содержание KERS206XSS

Страница 1: ...EDUCED BY INSTALLING A RANGE HOOD THAT PROJECTS HORIZONTALLY A MINIMUM OF 5 BEYOND THE BOTTOM OF THE CABINETS p n 316454912 rev A If the information in this manual is not followed exactly a fire or electrical shock may result causing property damage personal injury or death Important Notes to the Installer Readallinstructionscontainedintheseinstallationinstructions before installing range Remove a...

Страница 2: ...ll Need Power Supply Cord or Copper Electrical Wiring Metal Conduit for hard wiring NORMALINSTALLATIONSTEPS 3 16 pilot hole 1 3 4 deep The screws provided may be used in wood or concrete material Use a 5 16 nut driver or flat head screwdriver to secure the bracket in place See Fig 6 1c Level and Position Range Level range by adjusting the 4 leveling legs with a wrench NOTE A minimum clearance of 1...

Страница 3: ... Instructions Refer to Fig 12 Before wiring the range review the suggested power source location drawing in Fig 3 If connecting to a 4 Wire electrical system new branch circuit or mobile home requires 4 Wire connection 1 Follow the manufacturer s installation instructions supplied with the strain relief and install Also see Figs 9 10 11 2 Insert the end connectors for Line 1 Line 2 and Neutral and...

Страница 4: ... installation instructions supplied with the strain relief and install 2 3 4 Wire Permanent Connections Strip insulation away from the ends of the permanent wiring for Line 1 Line 2 Neutral also strip ground wire on 4 Wire Connections Tighten all 3 wire leads to the terminal block Follow wire locations shown in Fig 14 IMPORTANT NOTE DO NOT LOOSEN the factory installed nut connections which secure ...

Отзывы: