2
BUILT-IN OVEN SAFETY
INSTALLATION REQUIREMENTS
Tools and Parts
Gather the required tools and parts before starting installation.
Read and follow the instructions provided with any tools listed
here.
Tools needed
■
Phillips screwdriver
■
Measuring tape
■
Hand or electric drill (for wall cabinet installations)
■
1" (2.5 cm) drill bit (for wall cabinet installations)
■
Level
■
Flat-blade screwdriver
Parts needed
■
UL listed or CSA approved conduit connector
■
UL listed wire connectors
■
Warming Drawer Deflector Kit (for ovens installed above a
warming drawer)
Order Part Number W10489566 for white 27" (68.6 cm) kit
Order Part Number W10489564 for black 27" (68.6 cm) kit
Order Part Number W10489568 for stainless steel 27"
(68.6 cm) kit
Order Part Number W10489567 for white 30" (76.2 cm) kit
Order Part Number W10489565 for black 30" (76.2 cm) kit
Order Part Number W10489569 for stainless steel 30"
(76.2 cm) kit
To order, see the “Assistance or Service” section of the Use
and Care Guide.
Parts supplied
■
#8-14 x 1" screws - single ovens (2), double ovens (4)
■
Two #8-18 x
³⁄₈
" screws - bottom vent
■
Four #8-18 x
¹⁄₄
" screws - bottom vent trim
■
Four #8-18 x
³⁄₈
" screws - double oven feet
■
Bottom vent
■
Bottom vent trim
■
Two feet - double oven
■
Two front feet - double oven
■
Four grommets - single ovens (2), double ovens (4)*
■
Foam strip - single oven**
Check local codes. Check existing electrical supply. See
“Electrical Requirements.”
It is recommended that all electrical connections be made by a
licensed, qualified electrical installer.
*Grommets not required or included with models KEBK171B,
KEBK101B, KEBK276B, KEBK206B, KEBS179B, KEBS109B,
KEBS277B, KEBS279B, KEBS207B, KEBS209B, KEBU109B
and KEBU209B.
**Foam strip not included with double oven.
Location Requirements
IMPORTANT: Observe all governing codes and ordinances.
■
Cabinet opening dimensions that are shown must be used.
Given dimensions provide minimum clearance with oven.
■
Recessed installation area must provide complete enclosure
around the recessed portion of the oven.
■
Grounded electrical supply is required. See “Electrical
Requirements” section.
■
Electrical supply junction box should be located 3" (7.6 cm)
maximum below the support surface when the oven is
installed in a wall cabinet. A 1" (2.5 cm) minimum diameter
hole should have been drilled in the right rear or left rear
corner of the support surface to pass the appliance cable
through to the junction box.
NOTE: For undercounter installation, it is recommended that
the junction box be located in the adjacent right or left
cabinet. If you are installing the junction box on rear wall
behind oven, it is recommended that the junction box be
recessed and located in the upper center of the cabinet.
You can be killed or seriously injured if you don't immediately
You
can be killed or seriously injured if you don't follow
All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you what can
happen if the instructions are not followed.
Your safety and the safety of others are very important.
We have provided many important safety messages in this manual and on your appliance. Always read and obey all safety
messages.
This is the safety alert symbol.
This symbol alerts you to potential hazards that can kill or hurt you and others.
All safety messages will follow the safety alert symbol and either the word “DANGER” or “WARNING.”
These words mean:
follow instructions.
instructions.
DANGER
WARNING
