Kisae Abso Charger 12V 100A Скачать руководство пользователя страница 6

 

 

Page 

 

 

 

FCC INFORMATION  

This  equipment  has  been  tested  and  found  to  comply  with  the  limits  for  a  Class  B  digital  device, 
pursuant  to  part  15  of  the  FCC  Rules  and  comply  with  the  CE  EMC  Standard.  These  limits  are 
designed  to  provide  reasonable  protection  against  harmful  interference  in  a  residential  installation. 
This equipment can generate, use, and radiate radio frequency energy and, if not installed and used 
in  accordance  with  the  instructions,  may  cause  harmful  interference  to  radio  communications. 
However,  there  is  no  guarantee  that  interference  will  not  occur  in  a  particular  installation.  If  this 
equipment does cause harmful interference to radio or television reception, which can be determined 
by turning the equipment off and on, the user is encouraged to try to correct the interference by one 
or more of the following measures:  

 Reorient or relocate the receiving antenna.  

 Increase the separation between the equipment and the receiver.  

 Connect  the  equipment  into  an  outlet  on  a  circuit  different  from  that  to  which  the  receiver  is 

connected.  

 Consult the dealer or an experienced radio/TV technician for help.  

 

LIMITATIONS ON USE  

Do not use in connection with life support systems or other medical equipment or devices.  

 

 

Содержание Abso Charger 12V 100A



























Отзывы: