background image

12

INSTALLATION

INSTALLATION

Inside/Ceiling Mount

Mount the Installation Brackets

Mark 8" in from each jamb. This marks the 
center points of the two end brackets.

Mark the locations of any additional 
brackets, spaced evenly between the two 
end brackets.

Center the brackets on your marks and mark the screw holes.

The minimum casement depth for mounting the installation brackets is 

1

2

". 

Mark both of the winged screw holes with shallow mounting depths.

The minimum casement depth for a fully recessed mount varies with valance 
type and fabric cell size, as shown in the table. Mark the center screw hole 
when depth permits.

Drill the screw holes using a 

3

32

" drill bit.

CAUTION:  

Use drywall anchors when mounting into drywall. Use 

the drill bit size recommended by the manufacturer.

Attach the installation brackets using the screws provided.

IMPORTANT:  

Be sure the front edges of the installation brackets 

are level and aligned to each other. Use shims if necessary to level 
the brackets.

Mount the Headrail

Mount the headrail into the installation brackets. 
Do not remove any components from the headrail. 
Both end plates should remain attached to the 
ends of the headrail.

Place the front groove on the headrail onto the 
front lip of the installation bracket.

Position the end of the headrail opposite the 
fabric stack flush against the jamb. This leaves 
a gap on the stationary rail side. The stationary 
rail fills this gap when anchored.

Rotate the rear of the headrail up and push back until the headrail snaps in place.

Window/Door Opening

8"

Space Evenly

Jamb

Jamb

Space Evenly

8"

Place Groove onto

Front of Bracket

Snap in Place

Gap

Left Stack Shown

Flush

Minimum

1

2

"

Use Center Hole

When Depth Permits 

Valance 

Type

Fully Recessed Depth

3

4

" Cell

1

1

4

" Cell

Aluminum

3

7

8

"

4

5

8

"

Traditional

4

1

4

"

5"

Содержание Cellular Shade Collection



























Отзывы: