background image

16

INSTALLATION

OPERATION

Electronic Limit Adjustments

Electronic limits are set at the factory and normally do not require readjustment. For window treatments that may need additional 
adjustment or to set custom limit positions, go to Shade Settings in the Automation App to adjust limits. 

Level the Rail(s), If Necessary

 

Lift the bottom rail to locate the pockets on the underside of the rail.

 

With the middle rail on Top-Down/Bottom-Up shades, the pockets are on the top 
side of the rail.

 

See below for the middle rail adjustment on Day/Night shades.

 

Gently pull down on the bottom rail (or up on the middle rail) to fully insert the rail 
adjust key into the pocket. The key is fully inserted when the base of the key abuts to 
the pocket.

 

Lift up the rail slightly before turning the key. Turn the key clockwise to raise that 
side of the rail, or counter-clockwise to lower it.

 

One quarter turn of the key equals approximately 

1

4

".

IMPORTANT:  

The key must be fully inserted to avoid stripping the mechanism. Do not 

pull down on the rail while turning the key.

 

If there are more than two pockets, adjust the outer pockets first. Then adjust inner 
pockets as necessary, to maintain equal tension across the rail. As pocket adjustments 
are made, it is recommended that the shade be raised and lowered to check that it is 
level.

Adjusting the Day/Night Middle Rail

 

Hex pockets are found at the ends of the middle rail, which is located in the top cell of the 
lower fabric panel.

 

Insert the key so that its hex-shaped portion is about halfway into the pocket.

 

Turn the key clockwise to raise that end of the rail or counter-clockwise to lower it.

 

One full turn of the key equals approximately 

1

8

".

 

On shades over 60" wide, there will be two hex pockets in the right end of the middle rail. 
Use the rear hex pocket to adjust the tension in the center cord after adjusting the outer 
cords to level the rail.

Pocket

Underside of Bottom Rail

(or Top Side of Middle Rail)

Raise

Key

Lower

Raise

Adjusts

Center

Cord

Lower

Содержание Cellular Shade Automation III

























Отзывы: