Kirby Morgan M-48 SuperMask Скачать руководство пользователя страница 41

Страница: 41 / 56

Adjustments and Minor Repairs

Scheduled Maintenance

Kirby Morgan Dive Systems, Inc.

1430 Jason Way Santa Maria, California 93455

Phone: 805/928-7772 Fax: 805/928-0342

www.KirbyMorgan.com email: [email protected]

RBY

MORGA

E SYSTEMS, I

Page 1 of 1

M-48 SuperMask

Scheduled Maintenance

AC T I O N

F R E Q U E N CY

R E F E R E N C E

Pre-Dive Inspection

Before Each Use

"PRE-Dive Inspection" on page 27

2. Post-Dive Procedures

After Each Use

"Post-Dive Cleaning and Inspection" on
page 36

3. Inspection Of Pod Dewater-

ing/Purge Valve Assembly

Daily

4. Inspection of Pod Catch/Release and Pod Hook

Daily

5. Replace tie wraps

At Least Every
12 Months, In-
spect Daily

6. Inspect mouthpiece

Daily

7. Inspect head harness, buckle as-

semblies and strap keepers

Daily

8. Inspect Nose clearing device

Daily

NOTICE

Store spare valves, and soft goods in a cool, dark, dry
place. Avoid prolonged exposure to temperatures above
90 °F (32 °C) and/or exposure to ultraviolet rays or chemi-
cal fumes

Adjustments and Minor Repairs

Auto Purge Assembly

NOTE

This assembly is ONLY used with the Kirby Morgan Balanced
SCUBA regulator.

Cut tie wrap, and remove purge sleeve and purge tube as one unit.
Separate the two and set aside for inspection and reassembly.

2. Push on the outside of the pod skirt to unseat the water dump valve

body and valve. The two components will be removed as one unit
inside the pod skirt. Do not attempt to push the valve body through
the pod tube.

3. Clean all components using a soft bristle brush and cleaning solution.

4. Inspect components for damage. Replace if needed.

Содержание M-48 SuperMask

























































Результаты поиска

Содержание M-48 SuperMask

Отзывы:

Бренды по названию

Популярные бренды

Kirby Morgan M-48 SuperMask, Руководство пользователя

Результаты поиска

Содержание M-48 SuperMask

Отзывы:

Бренды по названию

Популярные бренды