manualshive.com logo in svg

Kirby Morgan M-48 SuperMask, Руководство пользователя

Поделиться
Скачать
Kirby Morgan M-48 SuperMask Скачать руководство пользователя страница 34

Mask Clearing and Dewatering

34

 

© MMXXI Kirby Morgan Dive Systems, Inc. All rights reserved. Document # 210902001

mouthpiece should be rotated downward to minimize the chance of free 
flowing. If the demand regulator is equipped with a bias adjustment or a 
venturi spoiler, the regulator should be desensitized and a free hand should 
also be at the ready to block the mouthpiece opening to stop a possible 
free flow caused by the venturi effect.

If switching from one pod or alternate air source to another, the pod or 
air source should be located and ready to use, prior to unhinging the pod 
to allow for rapid switching. Once the pod is completely free of the mask, 
another pod can be reattached or the user can use a standard open circuit 
SCUBA regulator. 

NOTE

Normal breathing can occur with the M-48 SuperMask

®

 without 

sealing the pod frame to the mask as long as the diver has the 
mouthpiece in their mouth and it is clear of water. With the 
mouthpiece secured and demand regulator/BOV/DSV cleared, 
the system will act in the same manner as a traditional mask and 
second stage when SCUBA diving.

B

 

WARNING

Never dive the pod without a mouthpiece installed. A 

mouthpiece allows use of the pod even if the pod is not 

sealed to the mask, or if the mask strap fails. Having a 

bite on the mouthpiece will help maintain a good seal to 

the mask.

Also, buddy breathing cannot be readily accomplished 

without a mouthpiece installed. The chances of an ac-

cident due to a compromised air supply increase greatly 

without the mouthpiece. This can lead to serious injury 

or death of the diver and/or the diver’s partner.

Mask Clearing and Dewatering

Mask Clearing with KMDSI Balanced SCUBA Regulator

To clear water from the Upper (eye) section, one should understand the 
path to exit. The water will be forced from the Upper (eye) section to the 
Lower (oral) cavity and out the dewatering/purge valve at the base of the 
pod frame. 

When using a KMDSI Balanced SCUBA Regulator with the SuperMask

®

 it is 

simply a matter of attaining a face forward position, with the mouthpiece 
in your mouth, and exhaling through your nose while using one hand to lift 
the bottom of the lens frame away from the face. Be sure to begin exhala-

Содержание M-48 SuperMask

























































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды