manualshive.com logo in svg

Kirby Morgan M-48 SuperMask, Руководство пользователя

Поделиться
Скачать
Kirby Morgan M-48 SuperMask Скачать руководство пользователя страница 26

Pre-Dive

26

 

© MMXXI Kirby Morgan Dive Systems, Inc. All rights reserved. Document # 210902001

Inspection

Regardless if your pod is fitted with a tilt to purge valve or with a purge 
tube, balanced there are two main points of inspection:

• 

The tie wrap securing the water dump body to the pod.

• 

The water dump valve body with valve and its fit into the recess 
inside the pod skirt.

Outside of the pod

Visually inspect the tie wrap for signs of failure then use your hand to ap-
ply slight pressure to the assembly to guarantee it is secured to the pod.

If your pod is outfitted with a tilt to purge valve assembly move the stem 
in all directions to ensure the spring is working and that the stem returns 
to its original position. 

Inside of the pod

Begin by visually confirming that the water dump valve body is seating 
correctly in the lower recess of the pod skirt.

Follow up by moving the tip of your finger around the leading edge of 
the Water Dump Valve Body to verify uniform seating into the pod skirt. 

B

 

CAUTION

Prior to diving, a complete inspection of the mask and all 

related gear should be made in accordance with the pre-

dive set up procedures and pre dive checklists to ensure 

that everything is in proper working order. Users should 

become familiar with all components and functions of the 

mask as well as all support equipment used before don-

ning the mask. Failure to inspect the mask prior to diving 

or being unfamiliar with the gear may lead to an accident 

resulting in injury or death.

PRE-DIVE with Open Circuit Regulator

Use “PRE-Dive Inspection”, in this user guide or print one out from www.
kirbymorgan.com/support/checklists to ensure that a methodical inspec-
tion of the M-48 SuperMask

®

 and all related gear is completed before each 

Содержание M-48 SuperMask

























































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды