manualshive.com logo in svg

Kirby Morgan M-48 SuperMask, Руководство пользователя

Поделиться
Скачать
Kirby Morgan M-48 SuperMask Скачать руководство пользователя страница 25

Pre-Dive

© MMXXI Kirby Morgan Dive Systems, Inc. All rights reserved. Document # 210902001

 

25

Communications with the M-48 SuperMask

®

VIDEO

How to install Communications in 
your M-48 MOD-1 / SuperMask® 
| Full Face Mask | 815-060

https://www.youtube.com/
watch?v=9jjf52OlHa8

Communications are available for the M-48 SuperMask

®

; either hard wire or 

wireless. The communications mounting instructions will vary, depending 
on what type of system you purchase.

To mount a microphone into the 
mask, follow the manufacturer’s rec-
ommended mounting instructions. 
In almost all cases, you will need to 
open up one of the communications 
ports, which are located below the 
bottom edge of the mask frame. 
Secure using tie wrap, KMDSI P/N 
520-038.

Installing a Communications Port Plug 

If the mask has a communications system installed, but you wish to use it 
without, remove the communications system from the mask. You will now 
need to plug the communications port. Install the communication port 
plug as shown, curved side towards the diver’s face.

Dewatering and Tilt to Purge Valve Assemblies

It is important to always clean and flush the purge tube, balanced or tilt 
to purge valve assembly after every dive; followed by an inspection for 
damage, tears or deterioration of assembly.

Содержание M-48 SuperMask

























































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды