manualshive.com logo in svg

Kirby Morgan M-48 SuperMask, Руководство пользователя

Поделиться
Скачать
Kirby Morgan M-48 SuperMask Скачать руководство пользователя страница 2

 

2

 

© MMXXI Kirby Morgan Dive Systems, Inc. All rights reserved. Document # 210902001

WARRANTY

USE ONLY KIRBY MORGAN

®

 GENUINE PARTS

Kirby Morgan Dive Systems Inc., (KMDSI) warrants every new helmet, BandMask

®

, Full Face Mask, SCUBA regula-

tor or air control system (KMACS 5) (each, a Product) to be free from defects in workmanship for a period of three 
hundred sixty five (365) days from the date of purchase from a KMDSI authorized dealer. This warranty covers all 
metal, fiberglass, and plastic parts, but does NOT cover rubber parts, communications components, head cushions, 
chin cushions, or foam spacers.

Any defect of the product in workmanship or material covered by this warranty discovered within three hun-
dred sixty five (365) days from the date of purchase must be promptly communicated in writing to the nearest 
authorized KMDSI dealer or (if no such dealer in the buyer’s country) contact KMDSI directly at (805) 928-
7772. No Product returns will be accepted by KMDSI without a returned merchandise authorization (RMA) 
number from KMDSI. Upon receipt of the RMA from KMDSI, the buyer should return the defective Product 
or part, freight prepaid, to an authorized KMDSI dealer or the KMDSI plant, as directed by the RMA depart-
ment. KMDSI will repair or replace the Product at no charge, within a reasonable time, as it deems necessary. 

THIS WARRANTY IS NULL AND VOID IF:

1)   The Product is not registered with KMDSI within ten (10) days of purchase, or

2)  The Product has not been properly serviced and/or maintained by KMDSI factory trained/approved personnel, 
according to factory recommended procedures provided in the manual, along with the KMDSI Appendices Checklists, 
and/or Product updates have not been performed as recommended by KMDSI, or

3)   Unauthorized attachments or modifications have been made to the Product, or 

4)   The Product has been used for purposes other than those for which it was designed, or otherwise has been abused, 
misused, or subjected to unusual conditions, or the Product’s intended service has been exceeded.

EXCEPT AS SPECIFICALLY PROVIDED HEREIN, THERE ARE NO OTHER WARRANTIES, EXPRESS OR 
IMPLIED, INCLUDING, BUT NOT LIMITED TO, ANY IMPLIED WARRANTIES FOR MERCHANTABILITY 
OR FITNESS FOR A PARTICULAR PURPOSE.  THE  HELMETS, BANDMASKS AND AIR CONTROL 
SYSTEMS COVERED BY THIS WARRANTY ARE MARKETED AND SOLD BY KMDSI SOLELY FOR COM-
MERCIAL OR INDUSTRIAL USE AND ARE NOT A CONSUMER PRODUCT INTENDED FOR PERSONAL, 
FAMILY, OR HOUSEHOLD USE.

In purchasing any Product subject to this warranty, the buyer agrees that its sole and exclusive remedy and KMDSI’s 
entire obligation in contract, tort, or otherwise under this contract will be repair or replacement at KMDSI’s option of 
the Product or any parts which KMDSI determines during the applicable warranty period are defective in workmanship 
or material covered by this warranty.  All exchanged parts are the property of KMDSI.  The buyer’s exclusive remedy 
and KMDSI’s entire liability in contract, tort, or otherwise is the payment by KMDSI of the buyer’s actual damages 
up to but not to exceed the amount paid by the buyer for the Product.

In no event shall KMDSI be liable to the buyer for indirect, special, incidental or consequential damages (including, 
but not limited to, damages for lost profits, lost sales, loss of business opportunity, or for injury to persons or property 
arising out of the use of the Products).  Any claim or action for breach of warranty must be commenced within one 
year following delivery of the Product to the buyer.

Buyer acknowledges that this warranty is the sole and exclusive warranty of the Product and that it supersedes any 
and all oral or written representations and undertakings between KMDSI, its dealers, and the buyer relating to the 
Products.  This warranty allocates the risks of product failure between KMDSI and the buyer, which allocation is 
recognized by both parties and is reflected in the price of the goods.  The buyer acknowledges that they have read 
this agreement, understand it, and are bound by its terms.

IMPORTANT:

 Please register your purchase online at 

www.kirbymorgan.com/support/product-registration-form

. If 

you have a problem with the online registration, please contact your Kirby Morgan dealer, or Kirby Morgan directly 
by calling (805) 928-7772, or email [email protected].

Kirby Morgan

®

 thanks you for your purchase.

Содержание M-48 SuperMask

























































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды