manualshive.com logo in svg

Kirby Morgan M-48 SuperMask, Руководство пользователя

Поделиться
Скачать
Kirby Morgan M-48 SuperMask Скачать руководство пользователя страница 16

Pre-Dive

16

 

© MMXXI Kirby Morgan Dive Systems, Inc. All rights reserved. Document # 210902001

Pre-Dive

B

 

WARNING

Not all SCUBA regulators/BOV’S/DSV’s will fit the M-48 

standard SCUBA pod. The size of the mouthpiece mount-

ing tube as well as the placement and size of the exhaust 

tee can affect the mounting and proper functioning of the 

mouthpiece and folding action on the pod bellows.

Mounting Open Circuit Regulators

VIDEO

How To Mount Open Circuit Regulators 
to a Kirby Morgan SCUBA pod

https://www.youtube.com/
watch?v=cPXJ-VueVy0

B

 

WARNING

Regarding Second Stages Used with M-48 SuperMask and 

M-48 MOD 1:

Testing conditions of the M-48 SuperMask

®

 and MOD-1 

masks using pilot assisted, or servo regulators, were 

found to exhibit higher levels of internal mask pressures 

when applying the purge button feature. These levels 

were above the allowable limit. This should be taken into 

consideration when choosing a second stage regulator 

for use with either mask.

If your mask was not supplied with a KMDSI regulator installed by the fac-
tory, you will need to have an acceptable regulator installed in the SCUBA 
pod, P/N 805-015.

Prior to installation check to see if your regulator will work properly with 
the SCUBA pod, P/N 805-015 by referencing the images that follow and 
conforming to the following parameters:

1. 

The regulator mounting tube must have a single lip at the end that will 
be closest to the diver’s mouth.

2.  Demand regulator mouthpiece mount tubes should be at least a length 

of 0.5 inches/1.27 cm at the shortest measurement.

Содержание M-48 SuperMask

























































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды