manualshive.com logo in svg

Kirby Morgan M-48 SuperMask, Руководство пользователя

Поделиться
Скачать
Kirby Morgan M-48 SuperMask Скачать руководство пользователя страница 14

Diving Modes

14

 

© MMXXI Kirby Morgan Dive Systems, Inc. All rights reserved. Document # 210902001

The mask should only be used for surface supplied diving by divers trained 
and qualified in surface supplied techniques and procedures. A fully func-
tional emergency gas supply system and body harness must always be 
used when diving the SuperMask

®

 or any of the KMDSI full face masks 

models in the surface supplied mode.

The mask has not been CE approved for surface supplied diving and 
should not be used for surface supplied diving in countries conforming 
to CE standards

Users of the SuperMask

®

 should practice donning, doffing, pod removal, 

and replacement procedures on the surface, in the dry. Once the basic 
maneuvers have been practiced and the user is comfortable, the user can 
move into a calm, shallow, controlled body of water (5–10 feet/1–3 meters 
in depth).

It is recommended that persons with previous full face mask experience 
make at least one thirty minute indoctrination dive prior to open-water 
diving. Newly trained divers and divers not experienced in full face mask 
diving must complete a training course in surface supplied diving. Using 
the SuperMask

®

 is very easy, but as with all new equipment, training and 

practice is the key to enjoyable diving.

Minimum Equipment for Surface Supplied Diving 

The minimum equipment for surface supplied diving with this mask in-
cludes the following:

Содержание M-48 SuperMask

























































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды