manualshive.com logo in svg

Kirby Morgan M-48 SuperMask, Руководство пользователя

Поделиться
Скачать
Kirby Morgan M-48 SuperMask Скачать руководство пользователя страница 13

Diving Modes

© MMXXI Kirby Morgan Dive Systems, Inc. All rights reserved. Document # 210902001

 

13

B

 

WARNING

If the mask is used for surface supplied diving, do not 

connect the umbilical directly to the M-48 SCUBA pod 

regulator. This can create a direct pull on the mask and 

pod and does not allow for use of a one-way valve and 

EGS supply. Always connect the umbilical to a one-way 

valve on a manifold block assembly, which then can be 

properly secured to the diving harness. KMDSI Manifold 

Block KMDSI P/N 300-145, 300-150, or 300-155 is appropri-

ate for this purpose. Use of the manifold block requires 

surface supplied training.

Without the proper equipment for surface supply, the risks 

are many and can include: severe face squeeze, loss of 

mask, separation from air hose/umbilical, all of which can 

result in severe injury or death by drowning.

The minimum temperature for using the Balanced SCUBA and M-48 
SuperMask

®

 with a surface supply umbilical and KMDSI manifold block is 

32 °F (0.5 °C).

B

 

WARNING

When diving surface supply using a high pressure source, 

use only a high pressure source that has been filtered 

through a system that removes moisture down to at least 

-50 °F (-45 °C) to reduce the possibility of forming ice in 

the supply system. Ice has the potential to dangerously 

restrict or cut off a diver’s air supply, resulting in serious 

injury or death.

Surface Supplied Open Circuit Diving Mode

The SuperMask

®

 can be used for surface supplied diving when used with 

a surface supplied diving system.

When using the KMDSI SuperFlow

®

 and Balanced SCUBA regulator second 

stage, the mask can be used to depths of 130 FSW (39 msw) when sup-
plied with an air source capable of delivering at least 4.5 actual cubic feet 
of air per minute (acfm) (127 alpm) to the diver worn manifold assembly. 
An ordinary scuba regulator first stage connected to a diving cylinder on 
the surface with a long hose to the mask is not an acceptable arrangement 
for this purpose, no matter what type of regulator is used.

Содержание M-48 SuperMask

























































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды