background image

ELECTRICAL INFORMATION

TURNING THE SANDER ON/OFF 

This Sander comes with a 2 step activation safety switch, refer to Fig.3, 
which starts and stops the machine. To turn the Sander on: 
1. Push up on the emergency stop button (A) Fig.3 and lift the switch 

cover (B) as shown.  

2. Press the green On button (C) to start the Sander. 
3. To stop the Sander, you can either press the red Off button (D) or 

close the switch cover and push the large emergency stop button (E). 

 

RESET BUTTON (OVERLOAD PROTECTOR) 

This machine comes with an overload reset button (A) Fig.4. If the 
machine motor overheats, a safety mechanism stops the motor           
automatically. To prevent motor overheating, reduce load on motor or 
check voltage. Allow motor to cool down, then press the reset button and 
restart the machine. If the machine does not restart, wait an additional 5 
minutes before attempting to restart Sander. 
 

TURNING THE BUILT-IN DUST COLLECTOR ON/OFF  
(KC-790FX-DC ONLY) 

The On/Off switch (B) Fig.4 is used to turn the built-in Dust Collector on 
and off. To turn the Dust Collector “On”, lift the switch upwards (On      
position), to turn the Dust Collector “Off”, push the switch downwards (Off 
position).  
 
This switch comes with a removable safety key (C) Fig.4. When the   
safety key is removed from the switch and placed in a safe location, 
unauthorized persons or children can’t turn the switch to the On position. 
It is recommended to always remove the safety key from the switch 
whenever the sander is not in use. To remove the safety switch, make 
sure the switch is in the Off position and simply pull out the safety key. 
 

ELECTRICAL DIAGRAMS

Figure 3

Figure 4

Electrical Diagram 

KC-790FX-DC (220V)

Electrical Diagram 

KC-790FX-DC (110V)

Electrical Diagram 

KC-790FX (220V)

Electrical Diagram 

KC-790FX (110V)

Содержание KC-790FX














Отзывы: