King Industrial KC-5510G3 Скачать руководство пользователя страница 8

Страница: 8 / 8

MAINTENANCE & TROUBLESHOOTING

TROUBLE

Low pressure

Oil discharge in air

Insufficient output, low

discharge pressure

Excessive vibration/

compressor knocks

Compressor uses too

much oil

POSSIBLE CAUSE

Air leak in safety valve

Drain cock open

Restricted air filter

Defective throttle uploader

Improper oil viscosity

Too much oil in crankcase

Compressor overheated

Restricted air filter

Leaks in air lines, air valves, fittings...

Drive belt slipping

Drain valve open

Defective pressure gauge

Leaking head gasket

Worn piston, worn out rings

Defective check valve

Loose compressor, motor or guard

Compressor not level

Wrong oil being used

Compressor valves loose or broken

Check valve knocks at low pressure

Restricted air filter

Wrong oil viscosity

Oil level too high

Crankcase breather valve malfunction

Worn piston rings

Piston rings not seated.

CORRECTIVE ACTION

Check valve manually by pulling. If condition persists, replace.

Close drain cock

Clean or replace as necessary

Replace throttle uploader

Replace oil with SAE 30 non-detergent oil

Drain crankcase and fill to proper level

Air pressure regulated too high

Replace filter

Replace worn components

Tension V-belt

Close drain valve

Replace pressure gauge

Replace head gasket

Replace worn parts

Clean check valve or replace

Tighten components

Level compressor

Drain and replace with proper oil

Check and replace worn or damaged valves

Remove and clean check valve

Replace filter

Drain and replace oil

Fill with oil to proper level

Replace crankcase breather

Replace piston rings

Allow 100 hours of normal operation for new rings to seat

HONDA ENGINE SERVICE INFORMATION

IF YOU ARE EXPERIENCING PROBLEMS WITH THE HONDA ENGINE, DO NOT RETURN TO THE

RETAILER, READ THE MAINTENANCE SECTION OF THE HONDA INSTRUCTION MANUAL, IF THIS DOES

NOT HELP YOU, CONTACT HONDA CANADA, INC. BY PHONE OR THROUGH THEIR WEB SITE FOR

SERVICE/REPAIR INFORMATION.

TOLL FREE: 1-888-9HONDA9 (946-6329) or WEB SITE: www.honda.ca

REPLACING/TENSIONING DRIVE BELT

If the drive belt needs tensioning, the belt should be adjusted so when pressure is
applied in the centre, there is approximately 1/2” slack. See Fig.8.

1) To install a new belt, remove belt guard. Loosen engine mount bolts and slide engine

towards the pump, remove belt.

2) Install proper replacement belt, slide engine away from pump to provide

recommended tension, align pulleys and fasten engine mount bolts.

3) Reinstall belt guard. Belt tension should be checked after 20 hours of operation.

Check belt tension monthly thereafter.

FIGURE 8

PARTS DIAGRAM & PARTS LISTS

Refer to the Parts section of the King Canada web site for the most updated parts diagram and parts list.

Содержание KC-5510G3








Результаты поиска

Содержание KC-5510G3

Отзывы:

King Industrial KC-5510G3, Инструкция по эксплуатации, Страница: 8 / 8

Результаты поиска

Содержание KC-5510G3

Отзывы: