Note:
Read this entire document, in addition to the Installation Manual, before installing
or using the KiloVault HAB™. Failure to do so or to follow any of the instructions
or warnings in this document can result in electrical shock, serious injury, or
death, or can damage the HAB™, potentially rendering it inoperable.
• Prior to installing your HAB™, please take pictures of the label on the left side,
including the serial number, serial number bar-code, QR code, and MAC
address. Store this information for your records, it is valuable and may be nec-
essary for system configuration or troubleshooting. Depending on your HAB™
unit’s position, viewing this information after installation may be difficult.
• It may be easier to open the tabs at the bottom (along the sides) of the box and
remove the box from the pallet, rather than removing the top lid and lifting the
HAB™ with the handles.
3
5
6
•
Turn On the HAB™ before removing from crate.
•
Turn on unit by holding the power button for 3-5 seconds.
•
(Hold until green RUN LED flashes)
•
Turn On the inverters main DC input disconnect Breaker.
•
Turn On the HAB™ DC Breaker.
•
Turn On the HAB™ using Power button , Press and hold for
3-5 seconds until the GREEN RUN LED flashes.
HAB™
QUICK START GUIDE
330 Codman Hill Road, Boxborough, MA 01719 | +1(888)218–5924 | [email protected] | www.kilovault.com
4
•
With the battery breaker off, and HAB™ power Off (Using the
Power button )
•
Connect proper DC cabling to the terminals of the HAB™
•
Ensure all terminals bolts are torqued to specs.
1
•
While the HAB™ is still in its crate, Register the KiloVault HAB™
•
Download the KiloVault HAB iT app and Activate the HAB™ on
the Cloud.
2
•
After the communication cables are connected.
•
Set the HAB™ address using the address DIP switch
NOTE
Refer to 4.6.7 Setting the HAB™ Address, of HAB Users Manual.
NOTE
Failure to activate the HAB™ on the CLOUD using the KiloVault iT app
will void the Warranty.
Scan the QR code with your mobile device to be redirected to the
KiloVault registration page.
NOTE
Refer to 4.6.1. Connecting the HAB™, of Users Manual.
DO NOT reverse the polarity (positive and negative) of your unit’s connec-
tions. NEVER short circuit your KiloVault® HAB™.
Registration
NOTE
Refer to 4.2. Unpacking the KiloVault® HAB™,of users Manual.
Available on the KiloVault website.
Unboxing
Connecting
the HAB™
Setting the HAB™
Address
Powering Up
the HAB
Mounting and Securing
the HAB™
•
Using sufficient resources lift the HAB™ onto the wall
bracket. Using the two M8*16mm bolts provided, secure
the HAB™ to the wall bracket.
•
We strongly recommend using lift equipment and straps to
secure and steady the KiloVault® HAB™.
QuickStartGuide_HAB_edit.indd 1
QuickStartGuide_HAB_edit.indd 1
11/23/22 2:22 PM
11/23/22 2:22 PM
Note:
Read this entire document, in addition to the Installation Manual, before installing
or using the KiloVault HAB™. Failure to do so or to follow any of the instructions
or warnings in this document can result in electrical shock, serious injury, or
death, or can damage the HAB™, potentially rendering it inoperable.
• Prior to installing your HAB™, please take pictures of the label on the left side,
including the serial number, serial number bar-code, QR code, and MAC
address. Store this information for your records, it is valuable and may be nec-
essary for system configuration or troubleshooting. Depending on your HAB™
unit’s position, viewing this information after installation may be dif
ficult.
• It may be easier to open the tabs at the bottom (along the sides) of the box and
remove the box from the pallet, rather than removing the top lid and lifting the
HAB™ with the handles.
3
5
6
•
Turn O
n the HAB™ befor
e remo
ving from cr
ate.
•
Turn on unit b
y holding the po
wer
button f
or 3-5 sec
onds.
•
(Hold un
til gr
een RUN LED flashes)
•
Turn O
n the invert
ers main DC input disconnect Br
eaker
.
•
Turn O
n the HAB™ DC Break
er.
•
Turn O
n the HAB™ using Pow
er butt
on , Press and hold f
or
3-5 seconds un
til the GREEN RUN LED flashes.
HAB™
QUICK S
TAR
T GUIDE
330 Codman Hill Road, Boxborough, MA 01719 | +1(888)218–5924 | [email protected] | www
.kilovault.com
4
•
With the ba
ttery
break
er o
ff, and HAB™ po
wer
Off (U
sing the
Pow
er butt
on
)
•
Connect proper
DC cabling to the t
erminals of the HAB™
•
Ensur
e all terminals bolts ar
e tor
qued to specs.
1
•
While the HAB™ is still in its cr
ate, R
egister
the KiloVault HAB™
•
Download the Kilo
Vault HAB iT
app and Activ
ate the HAB™ on
the Cloud.
2
•
Aft
er the c
ommunication cables ar
e connect
ed.
•
Set the HAB™ addr
ess using the address DIP
swit
ch
NOTE
Ref
er to 4.6.
7 Setting the HAB™
Addr
ess, of HAB U
sers Manual.
NOTE
Failur
e to activ
ate the HAB™ on the CL
OUD using the KiloVault iT
app
will v
oid the W
arranty
.
Scan the QR code
with your
mobile devic
e to be r
edirect
ed to the
KiloVault r
egistration page.
NOTE
Refer to 4.6.1. Connecting the HAB™, of Users Manual.
DO NOT reverse the polarity (positive and negative) of your unit’
s connec-
tions. NEVER short circuit your KiloVault® HAB™.
Registration
NOTE
Ref
er to 4.2. U
npacking the KiloVault® HAB™,o
f users M
anual.
Available on the Kilo
Vault
websit
e.
Unboxing
Connecting
the HAB™
Setting the HAB™
Address
Powering Up
the HAB
Mounting and
Securing
the HAB™
•
Using sufficien
t resour
ces lift the HAB™ on
to the
wall
brack
et. U
sing the two M8*16mm bolts pr
ovided, secur
e
the HAB™ to the
wall
brack
et.
•
We str
ongly r
ecommend using lift equipmen
t and straps t
o
secure and st
eady the Kilo
Vault® HAB™.
QuickStartGuide_HAB_edit.indd 1
QuickStartGuide_HAB_edit.indd 1
11/23/22 2:22 PM
11/23/22 2:22 PM
Note:
Read this entire document, in addition to the Installation Manual, before installing
or using the KiloVault HAB™. Failure to do so or to follow any of the instructions
or warnings in this document can result in electrical shock, serious injury, or
death, or can damage the HAB™, potentially rendering it inoperable.
• Prior to installing your HAB™, please take pictures of the label on the left side,
including the serial number, serial number bar-code, QR code, and MAC
address. Store this information for your records, it is valuable and may be nec-
essary for system configuration or troubleshooting. Depending on your HAB™
unit’s position, viewing this information after installation may be dif
ficult.
• It may be easier to open the tabs at the bottom (along the sides) of the box and
remove the box from the pallet, rather than removing the top lid and lifting the
HAB™ with the handles.
3
5
6
•
Turn O
n the HAB™ befor
e remo
ving from cr
ate.
•
Turn on unit b
y holding the po
wer
button f
or 3-5 sec
onds.
•
(Hold un
til gr
een RUN LED flashes)
•
Turn O
n the invert
ers main DC input disconnect Br
eaker
.
•
Turn O
n the HAB™ DC Break
er.
•
Turn O
n the HAB™ using Pow
er butt
on , Press and hold f
or
3-5 seconds un
til the GREEN RUN LED flashes.
HAB™
QUICK S
TAR
T GUIDE
330 Codman Hill Road, Boxborough, MA 01719 | +1(888)218–5924 | [email protected] | www
.kilovault.com
4
•
With the ba
ttery
break
er o
ff, and HAB™ po
wer
Off (U
sing the
Pow
er butt
on
)
•
Connect proper
DC cabling to the t
erminals of the HAB™
•
Ensur
e all terminals bolts ar
e tor
qued to specs.
1
•
While the HAB™ is still in its cr
ate, R
egister
the KiloVault HAB™
•
Download the Kilo
Vault HAB iT
app and Activ
ate the HAB™ on
the Cloud.
2
•
Aft
er the c
ommunication cables ar
e connect
ed.
•
Set the HAB™ addr
ess using the address DIP
swit
ch
NOTE
Ref
er to 4.6.
7 Setting the HAB™
Addr
ess, of HAB U
sers Manual.
NOTE
Failur
e to activ
ate the HAB™ on the CL
OUD using the KiloVault iT
app
will v
oid the W
arranty
.
Scan the QR code
with your
mobile devic
e to be r
edirect
ed to the
KiloVault r
egistration page.
NOTE
Refer to 4.6.1. Connecting the HAB™, of Users Manual.
DO NOT reverse the polarity (positive and negative) of your unit’
s connec-
tions. NEVER short circuit your KiloVault® HAB™.
Registration
NOTE
Ref
er to 4.2. U
npacking the KiloVault® HAB™,o
f users M
anual.
Available on the Kilo
Vault
websit
e.
Unboxing
Connecting
the HAB™
Setting the HAB™
Address
Powering Up
the HAB
Mounting and
Securing
the HAB™
•
Using sufficien
t resour
ces lift the HAB™ on
to the
wall
brack
et. U
sing the two M8*16mm bolts pr
ovided, secur
e
the HAB™ to the
wall
brack
et.
•
We str
ongly r
ecommend using lift equipmen
t and straps t
o
secure and st
eady the Kilo
Vault® HAB™.
QuickStartGuide_HAB_edit.indd 1
QuickStartGuide_HAB_edit.indd 1
11/23/22 2:22 PM
11/23/22 2:22 PM
Note:
Read this entire document, in addition to the Installation Manual, before installing
or using the KiloVault HAB™. Failure to do so or to follow any of the instructions
or warnings in this document can result in electrical shock, serious injury, or
death, or can damage the HAB™, potentially rendering it inoperable.
• Prior to installing your HAB™, please take pictures of the label on the left side,
including the serial number, serial number bar-code, QR code, and MAC
address. Store this information for your records, it is valuable and may be nec-
essary for system configuration or troubleshooting. Depending on your HAB™
unit’s position, viewing this information after installation may be difficult.
• It may be easier to open the tabs at the bottom (along the sides) of the box and
remove the box from the pallet, rather than removing the top lid and lifting the
HAB™ with the handles.
3
5
6
•
Turn On the HAB™ before removing from crate.
•
Turn on unit by holding the power button for 3-5 seconds.
•
(Hold until green RUN LED flashes)
•
Turn On the inverters main DC input disconnect Breaker.
•
Turn On the HAB™ DC Breaker.
•
Turn On the HAB™ using Power button , Press and hold for
3-5 seconds until the GREEN RUN LED flashes.
HAB™
QUICK START GUIDE
330 Codman Hill Road, Boxborough, MA 01719 | +1(888)218–5924 | [email protected] | www.kilovault.com
4
•
With the battery breaker off, and HAB™ power Off (Using the
Power button )
•
Connect proper DC cabling to the terminals of the HAB™
•
Ensure all terminals bolts are torqued to specs.
1
•
While the HAB™ is still in its crate, Register the KiloVault HAB™
•
Download the KiloVault HAB iT app and Activate the HAB™ on
the Cloud.
2
•
After the communication cables are connected.
•
Set the HAB™ address using the address DIP switch
NOTE
Refer to 4.6.7 Setting the HAB™ Address, of HAB Users Manual.
NOTE
Failure to activate the HAB™ on the CLOUD using the KiloVault iT app
will void the Warranty.
Scan the QR code with your mobile device to be redirected to the
KiloVault registration page.
NOTE
Refer to 4.6.1. Connecting the HAB™, of Users Manual.
DO NOT reverse the polarity (positive and negative) of your unit’s connec-
tions. NEVER short circuit your KiloVault® HAB™.
Registration
NOTE
Refer to 4.2. Unpacking the KiloVault® HAB™,of users Manual.
Available on the KiloVault website.
Unboxing
Connecting
the HAB™
Setting the HAB™
Address
Powering Up
the HAB
Mounting and Securing
the HAB™
•
Using sufficient resources lift the HAB™ onto the wall
bracket. Using the two M8*16mm bolts provided, secure
the HAB™ to the wall bracket.
•
We strongly recommend using lift equipment and straps to
secure and steady the KiloVault® HAB™.
QuickStartGuide_HAB_edit.indd 1
QuickStartGuide_HAB_edit.indd 1
11/23/22 2:22 PM
11/23/22 2:22 PM
Note:
Read this entire document, in addition to the Installation Manual, before installing
or using the KiloVault HAB™. Failure to do so or to follow any of the instructions
or warnings in this document can result in electrical shock, serious injury, or
death, or can damage the HAB™, potentially rendering it inoperable.
• Prior to installing your HAB™, please take pictures of the label on the left side,
including the serial number, serial number bar-code, QR code, and MAC
address. Store this information for your records, it is valuable and may be nec-
essary for system configuration or troubleshooting. Depending on your HAB™
unit’s position, viewing this information after installation may be difficult.
• It may be easier to open the tabs at the bottom (along the sides) of the box and
remove the box from the pallet, rather than removing the top lid and lifting the
HAB™ with the handles.
3
5
6
•
Turn On the HAB™ before removing from crate.
•
Turn on unit by holding the power button for 3-5 seconds.
•
(Hold until green RUN LED flashes)
•
Turn On the inverters main DC input disconnect Breaker.
•
Turn On the HAB™ DC Breaker.
•
Turn On the HAB™ using Power button , Press and hold for
3-5 seconds until the GREEN RUN LED flashes.
HAB™
QUICK START GUIDE
330 Codman Hill Road, Boxborough, MA 01719 | +1(888)218–5924 | [email protected] | www.kilovault.com
4
•
With the battery breaker off, and HAB™ power Off (Using the
Power button )
•
Connect proper DC cabling to the terminals of the HAB™
•
Ensure all terminals bolts are torqued to specs.
1
•
While the HAB™ is still in its crate, Register the KiloVault HAB™
•
Download the KiloVault HAB iT app and Activate the HAB™ on
the Cloud.
2
•
After the communication cables are connected.
•
Set the HAB™ address using the address DIP switch
NOTE
Refer to 4.6.7 Setting the HAB™ Address, of HAB Users Manual.
NOTE
Failure to activate the HAB™ on the CLOUD using the KiloVault iT app
will void the Warranty.
Scan the QR code with your mobile device to be redirected to the
KiloVault registration page.
NOTE
Refer to 4.6.1. Connecting the HAB™, of Users Manual.
DO NOT reverse the polarity (positive and negative) of your unit’s connec-
tions. NEVER short circuit your KiloVault® HAB™.
Registration
NOTE
Refer to 4.2. Unpacking the KiloVault® HAB™,of users Manual.
Available on the KiloVault website.
Unboxing
Connecting
the HAB™
Setting the HAB™
Address
Powering Up
the HAB
Mounting and Securing
the HAB™
•
Using sufficient resources lift the HAB™ onto the wall
bracket. Using the two M8*16mm bolts provided, secure
the HAB™ to the wall bracket.
•
We strongly recommend using lift equipment and straps to
secure and steady the KiloVault® HAB™.
QuickStartGuide_HAB_edit.indd 1
QuickStartGuide_HAB_edit.indd 1
11/23/22 2:22 PM
11/23/22 2:22 PM
Note:
Read this entire document, in addition to the Installation Manual, before installing
or using the KiloVault HAB™. Failure to do so or to follow any of the instructions
or warnings in this document can result in electrical shock, serious injury, or
death, or can damage the HAB™, potentially rendering it inoperable.
• Prior to installing your HAB™, please take pictures of the label on the left side,
including the serial number, serial number bar-code, QR code, and MAC
address. Store this information for your records, it is valuable and may be nec-
essary for system configuration or troubleshooting. Depending on your HAB™
unit’s position, viewing this information after installation may be dif
ficult.
• It may be easier to open the tabs at the bottom (along the sides) of the box and
remove the box from the pallet, rather than removing the top lid and lifting the
HAB™ with the handles.
3
5
6
•
Turn O
n the HAB™ befor
e remo
ving from cr
ate.
•
Turn on unit b
y holding the po
wer
button f
or 3-5 sec
onds.
•
(Hold un
til gr
een RUN LED flashes)
•
Turn O
n the invert
ers main DC input disconnect Br
eaker
.
•
Turn O
n the HAB™ DC Break
er.
•
Turn O
n the HAB™ using Pow
er butt
on , Press and hold f
or
3-5 seconds un
til the GREEN RUN LED flashes.
HAB™
QUICK S
TAR
T GUIDE
330 Codman Hill Road, Boxborough, MA 01719 | +1(888)218–5924 | [email protected] | www
.kilovault.com
4
•
With the ba
ttery
break
er o
ff, and HAB™ po
wer
Off (U
sing the
Pow
er butt
on
)
•
Connect proper
DC cabling to the t
erminals of the HAB™
•
Ensur
e all terminals bolts ar
e tor
qued to specs.
1
•
While the HAB™ is still in its cr
ate, R
egister
the KiloVault HAB™
•
Download the Kilo
Vault HAB iT
app and Activ
ate the HAB™ on
the Cloud.
2
•
Aft
er the c
ommunication cables ar
e connect
ed.
•
Set the HAB™ addr
ess using the address DIP
swit
ch
NOTE
Ref
er to 4.6.
7 Setting the HAB™
Addr
ess, of HAB U
sers Manual.
NOTE
Failur
e to activ
ate the HAB™ on the CL
OUD using the KiloVault iT
app
will v
oid the W
arranty
.
Scan the QR code
with your
mobile devic
e to be r
edirect
ed to the
KiloVault r
egistration page.
NOTE
Refer to 4.6.1. Connecting the HAB™, of Users Manual.
DO NOT reverse the polarity (positive and negative) of your unit’
s connec-
tions. NEVER short circuit your KiloVault® HAB™.
Registration
NOTE
Ref
er to 4.2. U
npacking the KiloVault® HAB™,o
f users M
anual.
Available on the Kilo
Vault
websit
e.
Unboxing
Connecting
the HAB™
Setting the HAB™
Address
Powering Up
the HAB
Mounting and
Securing
the HAB™
•
Using sufficien
t resour
ces lift the HAB™ on
to the
wall
brack
et. U
sing the two M8*16mm bolts pr
ovided, secur
e
the HAB™ to the
wall
brack
et.
•
We str
ongly r
ecommend using lift equipmen
t and straps t
o
secure and st
eady the Kilo
Vault® HAB™.
QuickStartGuide_HAB_edit.indd 1
QuickStartGuide_HAB_edit.indd 1
11/23/22 2:22 PM
11/23/22 2:22 PM
Note:
Read this entire document, in addition to the Installation Manual, before installing
or using the KiloVault HAB™. Failure to do so or to follow any of the instructions
or warnings in this document can result in electrical shock, serious injury, or
death, or can damage the HAB™, potentially rendering it inoperable.
• Prior to installing your HAB™, please take pictures of the label on the left side,
including the serial number, serial number bar-code, QR code, and MAC
address. Store this information for your records, it is valuable and may be nec-
essary for system configuration or troubleshooting. Depending on your HAB™
unit’s position, viewing this information after installation may be dif
ficult.
• It may be easier to open the tabs at the bottom (along the sides) of the box and
remove the box from the pallet, rather than removing the top lid and lifting the
HAB™ with the handles.
3
5
6
•
Turn O
n the HAB™ befor
e remo
ving from cr
ate.
•
Turn on unit b
y holding the po
wer
button f
or 3-5 sec
onds.
•
(Hold un
til gr
een RUN LED flashes)
•
Turn O
n the invert
ers main DC input disconnect Br
eaker
.
•
Turn O
n the HAB™ DC Break
er.
•
Turn O
n the HAB™ using Pow
er butt
on , Press and hold f
or
3-5 seconds un
til the GREEN RUN LED flashes.
HAB™
QUICK S
TAR
T GUIDE
330 Codman Hill Road, Boxborough, MA 01719 | +1(888)218–5924 | [email protected] | www
.kilovault.com
4
•
With the ba
ttery
break
er o
ff, and HAB™ po
wer
Off (U
sing the
Pow
er butt
on
)
•
Connect proper
DC cabling to the t
erminals of the HAB™
•
Ensur
e all terminals bolts ar
e tor
qued to specs.
1
•
While the HAB™ is still in its cr
ate, R
egister
the KiloVault HAB™
•
Download the Kilo
Vault HAB iT
app and Activ
ate the HAB™ on
the Cloud.
2
•
Aft
er the c
ommunication cables ar
e connect
ed.
•
Set the HAB™ addr
ess using the address DIP
swit
ch
NOTE
Ref
er to 4.6.
7 Setting the HAB™
Addr
ess, of HAB U
sers Manual.
NOTE
Failur
e to activ
ate the HAB™ on the CL
OUD using the KiloVault iT
app
will v
oid the W
arranty
.
Scan the QR code
with your
mobile devic
e to be r
edirect
ed to the
KiloVault r
egistration page.
NOTE
Refer to 4.6.1. Connecting the HAB™, of Users Manual.
DO NOT reverse the polarity (positive and negative) of your unit’
s connec-
tions. NEVER short circuit your KiloVault® HAB™.
Registration
NOTE
Ref
er to 4.2. U
npacking the KiloVault® HAB™,o
f users M
anual.
Available on the Kilo
Vault
websit
e.
Unboxing
Connecting
the HAB™
Setting the HAB™
Address
Powering Up
the HAB
Mounting and
Securing
the HAB™
•
Using sufficien
t resour
ces lift the HAB™ on
to the
wall
brack
et. U
sing the two M8*16mm bolts pr
ovided, secur
e
the HAB™ to the
wall
brack
et.
•
We str
ongly r
ecommend using lift equipmen
t and straps t
o
secure and st
eady the Kilo
Vault® HAB™.
QuickStartGuide_HAB_edit.indd 1
QuickStartGuide_HAB_edit.indd 1
11/23/22 2:22 PM
11/23/22 2:22 PM
Note:
Read this entire document, in addition to the Installation Manual, before installing
or using the KiloVault HAB™. Failure to do so or to follow any of the instructions
or warnings in this document can result in electrical shock, serious injury, or
death, or can damage the HAB™, potentially rendering it inoperable.
• Prior to installing your HAB™, please take pictures of the label on the left side,
including the serial number, serial number bar-code, QR code, and MAC
address. Store this information for your records, it is valuable and may be nec-
essary for system configuration or troubleshooting. Depending on your HAB™
unit’s position, viewing this information after installation may be dif
ficult.
• It may be easier to open the tabs at the bottom (along the sides) of the box and
remove the box from the pallet, rather than removing the top lid and lifting the
HAB™ with the handles.
3
5
6
•
Turn O
n the HAB™ befor
e remo
ving from cr
ate.
•
Turn on unit b
y holding the po
wer
button f
or 3-5 sec
onds.
•
(Hold un
til gr
een RUN LED flashes)
•
Turn O
n the invert
ers main DC input disconnect Br
eaker
.
•
Turn O
n the HAB™ DC Break
er.
•
Turn O
n the HAB™ using Pow
er butt
on , Press and hold f
or
3-5 seconds un
til the GREEN RUN LED flashes.
HAB™
QUICK S
TAR
T GUIDE
330 Codman Hill Road, Boxborough, MA 01719 | +1(888)218–5924 | [email protected] | www
.kilovault.com
4
•
With the ba
ttery
break
er o
ff, and HAB™ po
wer
Off (U
sing the
Pow
er butt
on
)
•
Connect proper
DC cabling to the t
erminals of the HAB™
•
Ensur
e all terminals bolts ar
e tor
qued to specs.
1
•
While the HAB™ is still in its cr
ate, R
egister
the KiloVault HAB™
•
Download the Kilo
Vault HAB iT
app and Activ
ate the HAB™ on
the Cloud.
2
•
Aft
er the c
ommunication cables ar
e connect
ed.
•
Set the HAB™ addr
ess using the address DIP
swit
ch
NOTE
Ref
er to 4.6.
7 Setting the HAB™
Addr
ess, of HAB U
sers Manual.
NOTE
Failur
e to activ
ate the HAB™ on the CL
OUD using the KiloVault iT
app
will v
oid the W
arranty
.
Scan the QR code
with your
mobile devic
e to be r
edirect
ed to the
KiloVault r
egistration page.
NOTE
Refer to 4.6.1. Connecting the HAB™, of Users Manual.
DO NOT reverse the polarity (positive and negative) of your unit’
s connec-
tions. NEVER short circuit your KiloVault® HAB™.
Registration
NOTE
Ref
er to 4.2. U
npacking the KiloVault® HAB™,o
f users M
anual.
Available on the Kilo
Vault
websit
e.
Unboxing
Connecting
the HAB™
Setting the HAB™
Address
Powering Up
the HAB
Mounting and
Securing
the HAB™
•
Using sufficien
t resour
ces lift the HAB™ on
to the
wall
brack
et. U
sing the two M8*16mm bolts pr
ovided, secur
e
the HAB™ to the
wall
brack
et.
•
We str
ongly r
ecommend using lift equipmen
t and straps t
o
secure and st
eady the Kilo
Vault® HAB™.
QuickStartGuide_HAB_edit.indd 1
QuickStartGuide_HAB_edit.indd 1
11/23/22 2:22 PM
11/23/22 2:22 PM
Note:
Read this entire document, in addition to the Installation Manual, before installing
or using the KiloVault HAB™. Failure to do so or to follow any of the instructions
or warnings in this document can result in electrical shock, serious injury, or
death, or can damage the HAB™, potentially rendering it inoperable.
• Prior to installing your HAB™, please take pictures of the label on the left side,
including the serial number, serial number bar-code, QR code, and MAC
address. Store this information for your records, it is valuable and may be nec-
essary for system configuration or troubleshooting. Depending on your HAB™
unit’s position, viewing this information after installation may be dif
ficult.
• It may be easier to open the tabs at the bottom (along the sides) of the box and
remove the box from the pallet, rather than removing the top lid and lifting the
HAB™ with the handles.
3
5
6
•
Turn O
n the HAB™ befor
e remo
ving from cr
ate.
•
Turn on unit b
y holding the po
wer
button f
or 3-5 sec
onds.
•
(Hold un
til gr
een RUN LED flashes)
•
Turn O
n the invert
ers main DC input disconnect Br
eaker
.
•
Turn O
n the HAB™ DC Break
er.
•
Turn O
n the HAB™ using Pow
er butt
on , Press and hold f
or
3-5 seconds un
til the GREEN RUN LED flashes.
HAB™
QUICK S
TAR
T GUIDE
330 Codman Hill Road, Boxborough, MA 01719 | +1(888)218–5924 | [email protected] | www
.kilovault.com
4
•
With the ba
ttery
break
er o
ff, and HAB™ po
wer
Off (U
sing the
Pow
er butt
on
)
•
Connect proper
DC cabling to the t
erminals of the HAB™
•
Ensur
e all terminals bolts ar
e tor
qued to specs.
1
•
While the HAB™ is still in its cr
ate, R
egister
the KiloVault HAB™
•
Download the Kilo
Vault HAB iT
app and Activ
ate the HAB™ on
the Cloud.
2
•
Aft
er the c
ommunication cables ar
e connect
ed.
•
Set the HAB™ addr
ess using the address DIP
swit
ch
NOTE
Ref
er to 4.6.
7 Setting the HAB™
Addr
ess, of HAB U
sers Manual.
NOTE
Failur
e to activ
ate the HAB™ on the CL
OUD using the KiloVault iT
app
will v
oid the W
arranty
.
Scan the QR code
with your
mobile devic
e to be r
edirect
ed to the
KiloVault r
egistration page.
NOTE
Refer to 4.6.1. Connecting the HAB™, of Users Manual.
DO NOT reverse the polarity (positive and negative) of your unit’
s connec-
tions. NEVER short circuit your KiloVault® HAB™.
Registration
NOTE
Ref
er to 4.2. U
npacking the KiloVault® HAB™,o
f users M
anual.
Available on the Kilo
Vault
websit
e.
Unboxing
Connecting
the HAB™
Setting the HAB™
Address
Powering Up
the HAB
Mounting and
Securing
the HAB™
•
Using sufficien
t resour
ces lift the HAB™ on
to the
wall
brack
et. U
sing the two M8*16mm bolts pr
ovided, secur
e
the HAB™ to the
wall
brack
et.
•
We str
ongly r
ecommend using lift equipmen
t and straps t
o
secure and st
eady the Kilo
Vault® HAB™.
QuickStartGuide_HAB_edit.indd 1
QuickStartGuide_HAB_edit.indd 1
11/23/22 2:22 PM
11/23/22 2:22 PM
Note:
Read this entire document, in addition to the Installation Manual, before installing
or using the KiloVault HAB™. Failure to do so or to follow any of the instructions
or warnings in this document can result in electrical shock, serious injury, or
death, or can damage the HAB™, potentially rendering it inoperable.
• Prior to installing your HAB™, please take pictures of the label on the left side,
including the serial number, serial number bar-code, QR code, and MAC
address. Store this information for your records, it is valuable and may be nec-
essary for system configuration or troubleshooting. Depending on your HAB™
unit’s position, viewing this information after installation may be difficult.
• It may be easier to open the tabs at the bottom (along the sides) of the box and
remove the box from the pallet, rather than removing the top lid and lifting the
HAB™ with the handles.
3
5
6
•
Turn On the HAB™ before removing from crate.
•
Turn on unit by holding the power button for 3-5 seconds.
•
(Hold until green RUN LED flashes)
•
Turn On the inverters main DC input disconnect Breaker.
•
Turn On the HAB™ DC Breaker.
•
Turn On the HAB™ using Power button , Press and hold for
3-5 seconds until the GREEN RUN LED flashes.
HAB™
QUICK START GUIDE
330 Codman Hill Road, Boxborough, MA 01719 | +1(888)218–5924 | [email protected] | www.kilovault.com
4
•
With the battery breaker off, and HAB™ power Off (Using the
Power button )
•
Connect proper DC cabling to the terminals of the HAB™
•
Ensure all terminals bolts are torqued to specs.
1
•
While the HAB™ is still in its crate, Register the KiloVault HAB™
•
Download the KiloVault HAB iT app and Activate the HAB™ on
the Cloud.
2
•
After the communication cables are connected.
•
Set the HAB™ address using the address DIP switch
NOTE
Refer to 4.6.7 Setting the HAB™ Address, of HAB Users Manual.
NOTE
Failure to activate the HAB™ on the CLOUD using the KiloVault iT app
will void the Warranty.
Scan the QR code with your mobile device to be redirected to the
KiloVault registration page.
NOTE
Refer to 4.6.1. Connecting the HAB™, of Users Manual.
DO NOT reverse the polarity (positive and negative) of your unit’s connec-
tions. NEVER short circuit your KiloVault® HAB™.
Registration
NOTE
Refer to 4.2. Unpacking the KiloVault® HAB™,of users Manual.
Available on the KiloVault website.
Unboxing
Connecting
the HAB™
Setting the HAB™
Address
Powering Up
the HAB
Mounting and Securing
the HAB™
•
Using sufficient resources lift the HAB™ onto the wall
bracket. Using the two M8*16mm bolts provided, secure
the HAB™ to the wall bracket.
•
We strongly recommend using lift equipment and straps to
secure and steady the KiloVault® HAB™.
QuickStartGuide_HAB_edit.indd 1
QuickStartGuide_HAB_edit.indd 1
11/23/22 2:22 PM
11/23/22 2:22 PM
Note:
Read this entire document, in addition to the Installation Manual, before installing
or using the KiloVault HAB™. Failure to do so or to follow any of the instructions
or warnings in this document can result in electrical shock, serious injury, or
death, or can damage the HAB™, potentially rendering it inoperable.
• Prior to installing your HAB™, please take pictures of the label on the left side,
including the serial number, serial number bar-code, QR code, and MAC
address. Store this information for your records, it is valuable and may be nec-
essary for system configuration or troubleshooting. Depending on your HAB™
unit’s position, viewing this information after installation may be dif
ficult.
• It may be easier to open the tabs at the bottom (along the sides) of the box and
remove the box from the pallet, rather than removing the top lid and lifting the
HAB™ with the handles.
3
5
6
•
Turn O
n the HAB™ befor
e remo
ving from cr
ate.
•
Turn on unit b
y holding the po
wer
button f
or 3-5 sec
onds.
•
(Hold un
til gr
een RUN LED flashes)
•
Turn O
n the invert
ers main DC input disconnect Br
eaker
.
•
Turn O
n the HAB™ DC Break
er.
•
Turn O
n the HAB™ using Pow
er butt
on , Press and hold f
or
3-5 seconds un
til the GREEN RUN LED flashes.
HAB™
QUICK S
TAR
T GUIDE
330 Codman Hill Road, Boxborough, MA 01719 | +1(888)218–5924 | [email protected] | www
.kilovault.com
4
•
With the ba
ttery
break
er o
ff, and HAB™ po
wer
Off (U
sing the
Pow
er butt
on
)
•
Connect proper
DC cabling to the t
erminals of the HAB™
•
Ensur
e all terminals bolts ar
e tor
qued to specs.
1
•
While the HAB™ is still in its cr
ate, R
egister
the KiloVault HAB™
•
Download the Kilo
Vault HAB iT
app and Activ
ate the HAB™ on
the Cloud.
2
•
Aft
er the c
ommunication cables ar
e connect
ed.
•
Set the HAB™ addr
ess using the address DIP
swit
ch
NOTE
Ref
er to 4.6.
7 Setting the HAB™
Addr
ess, of HAB U
sers Manual.
NOTE
Failur
e to activ
ate the HAB™ on the CL
OUD using the KiloVault iT
app
will v
oid the W
arranty
.
Scan the QR code
with your
mobile devic
e to be r
edirect
ed to the
KiloVault r
egistration page.
NOTE
Refer to 4.6.1. Connecting the HAB™, of Users Manual.
DO NOT reverse the polarity (positive and negative) of your unit’
s connec-
tions. NEVER short circuit your KiloVault® HAB™.
Registration
NOTE
Ref
er to 4.2. U
npacking the KiloVault® HAB™,o
f users M
anual.
Available on the Kilo
Vault
websit
e.
Unboxing
Connecting
the HAB™
Setting the HAB™
Address
Powering Up
the HAB
Mounting and
Securing
the HAB™
•
Using sufficien
t resour
ces lift the HAB™ on
to the
wall
brack
et. U
sing the two M8*16mm bolts pr
ovided, secur
e
the HAB™ to the
wall
brack
et.
•
We str
ongly r
ecommend using lift equipmen
t and straps t
o
secure and st
eady the Kilo
Vault® HAB™.
QuickStartGuide_HAB_edit.indd 1
QuickStartGuide_HAB_edit.indd 1
11/23/22 2:22 PM
11/23/22 2:22 PM
Note:
Read this entire document, in addition to the Installation Manual, before installing
or using the KiloVault HAB™. Failure to do so or to follow any of the instructions
or warnings in this document can result in electrical shock, serious injury, or
death, or can damage the HAB™, potentially rendering it inoperable.
• Prior to installing your HAB™, please take pictures of the label on the left side,
including the serial number, serial number bar-code, QR code, and MAC
address. Store this information for your records, it is valuable and may be nec-
essary for system configuration or troubleshooting. Depending on your HAB™
unit’s position, viewing this information after installation may be dif
ficult.
• It may be easier to open the tabs at the bottom (along the sides) of the box and
remove the box from the pallet, rather than removing the top lid and lifting the
HAB™ with the handles.
3
5
6
•
Turn O
n the HAB™ befor
e remo
ving from cr
ate.
•
Turn on unit b
y holding the po
wer
button f
or 3-5 sec
onds.
•
(Hold un
til gr
een RUN LED flashes)
•
Turn O
n the invert
ers main DC input disconnect Br
eaker
.
•
Turn O
n the HAB™ DC Break
er.
•
Turn O
n the HAB™ using Pow
er butt
on , Press and hold f
or
3-5 seconds un
til the GREEN RUN LED flashes.
HAB™
QUICK S
TAR
T GUIDE
330 Codman Hill Road, Boxborough, MA 01719 | +1(888)218–5924 | [email protected] | www
.kilovault.com
4
•
With the ba
ttery
break
er o
ff, and HAB™ po
wer
Off (U
sing the
Pow
er butt
on
)
•
Connect proper
DC cabling to the t
erminals of the HAB™
•
Ensur
e all terminals bolts ar
e tor
qued to specs.
1
•
While the HAB™ is still in its cr
ate, R
egister
the KiloVault HAB™
•
Download the Kilo
Vault HAB iT
app and Activ
ate the HAB™ on
the Cloud.
2
•
Aft
er the c
ommunication cables ar
e connect
ed.
•
Set the HAB™ addr
ess using the address DIP
swit
ch
NOTE
Ref
er to 4.6.
7 Setting the HAB™
Addr
ess, of HAB U
sers Manual.
NOTE
Failur
e to activ
ate the HAB™ on the CL
OUD using the KiloVault iT
app
will v
oid the W
arranty
.
Scan the QR code
with your
mobile devic
e to be r
edirect
ed to the
KiloVault r
egistration page.
NOTE
Refer to 4.6.1. Connecting the HAB™, of Users Manual.
DO NOT reverse the polarity (positive and negative) of your unit’
s connec-
tions. NEVER short circuit your KiloVault® HAB™.
Registration
NOTE
Ref
er to 4.2. U
npacking the KiloVault® HAB™,o
f users M
anual.
Available on the Kilo
Vault
websit
e.
Unboxing
Connecting
the HAB™
Setting the HAB™
Address
Powering Up
the HAB
Mounting and
Securing
the HAB™
•
Using sufficien
t resour
ces lift the HAB™ on
to the
wall
brack
et. U
sing the two M8*16mm bolts pr
ovided, secur
e
the HAB™ to the
wall
brack
et.
•
We str
ongly r
ecommend using lift equipmen
t and straps t
o
secure and st
eady the Kilo
Vault® HAB™.
QuickStartGuide_HAB_edit.indd 1
QuickStartGuide_HAB_edit.indd 1
11/23/22 2:22 PM
11/23/22 2:22 PM
Note:
Read this entire document, in addition to the Installation Manual, before installing
or using the KiloVault HAB™. Failure to do so or to follow any of the instructions
or warnings in this document can result in electrical shock, serious injury, or
death, or can damage the HAB™, potentially rendering it inoperable.
• Prior to installing your HAB™, please take pictures of the label on the left side,
including the serial number, serial number bar-code, QR code, and MAC
address. Store this information for your records, it is valuable and may be nec-
essary for system configuration or troubleshooting. Depending on your HAB™
unit’s position, viewing this information after installation may be difficult.
• It may be easier to open the tabs at the bottom (along the sides) of the box and
remove the box from the pallet, rather than removing the top lid and lifting the
HAB™ with the handles.
3
5
6
•
Turn On the HAB™ before removing from crate.
•
Turn on unit by holding the power button for 3-5 seconds.
•
(Hold until green RUN LED flashes)
•
Turn On the inverters main DC input disconnect Breaker.
•
Turn On the HAB™ DC Breaker.
•
Turn On the HAB™ using Power button , Press and hold for
3-5 seconds until the GREEN RUN LED flashes.
HAB™
QUICK START GUIDE
330 Codman Hill Road, Boxborough, MA 01719 | +1(888)218–5924 | [email protected] | www.kilovault.com
4
•
With the battery breaker off, and HAB™ power Off (Using the
Power button )
•
Connect proper DC cabling to the terminals of the HAB™
•
Ensure all terminals bolts are torqued to specs.
1
•
While the HAB™ is still in its crate, Register the KiloVault HAB™
•
Download the KiloVault HAB iT app and Activate the HAB™ on
the Cloud.
2
•
After the communication cables are connected.
•
Set the HAB™ address using the address DIP switch
NOTE
Refer to 4.6.7 Setting the HAB™ Address, of HAB Users Manual.
NOTE
Failure to activate the HAB™ on the CLOUD using the KiloVault iT app
will void the Warranty.
Scan the QR code with your mobile device to be redirected to the
KiloVault registration page.
NOTE
Refer to 4.6.1. Connecting the HAB™, of Users Manual.
DO NOT reverse the polarity (positive and negative) of your unit’s connec-
tions. NEVER short circuit your KiloVault® HAB™.
Registration
NOTE
Refer to 4.2. Unpacking the KiloVault® HAB™,of users Manual.
Available on the KiloVault website.
Unboxing
Connecting
the HAB™
Setting the HAB™
Address
Powering Up
the HAB
Mounting and Securing
the HAB™
•
Using sufficient resources lift the HAB™ onto the wall
bracket. Using the two M8*16mm bolts provided, secure
the HAB™ to the wall bracket.
•
We strongly recommend using lift equipment and straps to
secure and steady the KiloVault® HAB™.
QuickStartGuide_HAB_edit.indd 1
QuickStartGuide_HAB_edit.indd 1
11/23/22 2:22 PM
11/23/22 2:22 PM
Note:
Read this entire document, in addition to the Installation Manual, before installing
or using the KiloVault HAB™. Failure to do so or to follow any of the instructions
or warnings in this document can result in electrical shock, serious injury, or
death, or can damage the HAB™, potentially rendering it inoperable.
• Prior to installing your HAB™, please take pictures of the label on the left side,
including the serial number, serial number bar-code, QR code, and MAC
address. Store this information for your records, it is valuable and may be nec-
essary for system configuration or troubleshooting. Depending on your HAB™
unit’s position, viewing this information after installation may be difficult.
• It may be easier to open the tabs at the bottom (along the sides) of the box and
remove the box from the pallet, rather than removing the top lid and lifting the
HAB™ with the handles.
3
5
6
•
Turn On the HAB™ before removing from crate.
•
Turn on unit by holding the power button for 3-5 seconds.
•
(Hold until green RUN LED flashes)
•
Turn On the inverters main DC input disconnect Breaker.
•
Turn On the HAB™ DC Breaker.
•
Turn On the HAB™ using Power button , Press and hold for
3-5 seconds until the GREEN RUN LED flashes.
HAB™
QUICK START GUIDE
330 Codman Hill Road, Boxborough, MA 01719 | +1(888)218–5924 | [email protected] | www.kilovault.com
4
•
With the battery breaker off, and HAB™ power Off (Using the
Power button )
•
Connect proper DC cabling to the terminals of the HAB™
•
Ensure all terminals bolts are torqued to specs.
1
•
While the HAB™ is still in its crate, Register the KiloVault HAB™
•
Download the KiloVault HAB iT app and Activate the HAB™ on
the Cloud.
2
•
After the communication cables are connected.
•
Set the HAB™ address using the address DIP switch
NOTE
Refer to 4.6.7 Setting the HAB™ Address, of HAB Users Manual.
NOTE
Failure to activate the HAB™ on the CLOUD using the KiloVault iT app
will void the Warranty.
Scan the QR code with your mobile device to be redirected to the
KiloVault registration page.
NOTE
Refer to 4.6.1. Connecting the HAB™, of Users Manual.
DO NOT reverse the polarity (positive and negative) of your unit’s connec-
tions. NEVER short circuit your KiloVault® HAB™.
Registration
NOTE
Refer to 4.2. Unpacking the KiloVault® HAB™,of users Manual.
Available on the KiloVault website.
Unboxing
Connecting
the HAB™
Setting the HAB™
Address
Powering Up
the HAB
Mounting and Securing
the HAB™
•
Using sufficient resources lift the HAB™ onto the wall
bracket. Using the two M8*16mm bolts provided, secure
the HAB™ to the wall bracket.
•
We strongly recommend using lift equipment and straps to
secure and steady the KiloVault® HAB™.
QuickStartGuide_HAB_edit.indd 1
QuickStartGuide_HAB_edit.indd 1
11/23/22 2:22 PM
11/23/22 2:22 PM
Note:
Read this entire document, in addition to the Installation Manual, before installing
or using the KiloVault HAB™. Failure to do so or to follow any of the instructions
or warnings in this document can result in electrical shock, serious injury, or
death, or can damage the HAB™, potentially rendering it inoperable.
• Prior to installing your HAB™, please take pictures of the label on the left side,
including the serial number, serial number bar-code, QR code, and MAC
address. Store this information for your records, it is valuable and may be nec-
essary for system configuration or troubleshooting. Depending on your HAB™
unit’s position, viewing this information after installation may be dif
ficult.
• It may be easier to open the tabs at the bottom (along the sides) of the box and
remove the box from the pallet, rather than removing the top lid and lifting the
HAB™ with the handles.
3
5
6
•
Turn O
n the HAB™ befor
e remo
ving from cr
ate.
•
Turn on unit b
y holding the po
wer
button f
or 3-5 sec
onds.
•
(Hold un
til gr
een RUN LED flashes)
•
Turn O
n the invert
ers main DC input disconnect Br
eaker
.
•
Turn O
n the HAB™ DC Break
er.
•
Turn O
n the HAB™ using Pow
er butt
on , Press and hold f
or
3-5 seconds un
til the GREEN RUN LED flashes.
HAB™
QUICK S
TAR
T GUIDE
330 Codman Hill Road, Boxborough, MA 01719 | +1(888)218–5924 | [email protected] | www
.kilovault.com
4
•
With the ba
ttery
break
er o
ff, and HAB™ po
wer
Off (U
sing the
Pow
er butt
on
)
•
Connect proper
DC cabling to the t
erminals of the HAB™
•
Ensur
e all terminals bolts ar
e tor
qued to specs.
1
•
While the HAB™ is still in its cr
ate, R
egister
the KiloVault HAB™
•
Download the Kilo
Vault HAB iT
app and Activ
ate the HAB™ on
the Cloud.
2
•
Aft
er the c
ommunication cables ar
e connect
ed.
•
Set the HAB™ addr
ess using the address DIP
swit
ch
NOTE
Ref
er to 4.6.
7 Setting the HAB™
Addr
ess, of HAB U
sers Manual.
NOTE
Failur
e to activ
ate the HAB™ on the CL
OUD using the KiloVault iT
app
will v
oid the W
arranty
.
Scan the QR code
with your
mobile devic
e to be r
edirect
ed to the
KiloVault r
egistration page.
NOTE
Refer to 4.6.1. Connecting the HAB™, of Users Manual.
DO NOT reverse the polarity (positive and negative) of your unit’
s connec-
tions. NEVER short circuit your KiloVault® HAB™.
Registration
NOTE
Ref
er to 4.2. U
npacking the KiloVault® HAB™,o
f users M
anual.
Available on the Kilo
Vault
websit
e.
Unboxing
Connecting
the HAB™
Setting the HAB™
Address
Powering Up
the HAB
Mounting and
Securing
the HAB™
•
Using sufficien
t resour
ces lift the HAB™ on
to the
wall
brack
et. U
sing the two M8*16mm bolts pr
ovided, secur
e
the HAB™ to the
wall
brack
et.
•
We str
ongly r
ecommend using lift equipmen
t and straps t
o
secure and st
eady the Kilo
Vault® HAB™.
QuickStartGuide_HAB_edit.indd 1
QuickStartGuide_HAB_edit.indd 1
11/23/22 2:22 PM
11/23/22 2:22 PM
Note:
Read this entire document, in addition to the Installation Manual, before installing
or using the KiloVault HAB™. Failure to do so or to follow any of the instructions
or warnings in this document can result in electrical shock, serious injury, or
death, or can damage the HAB™, potentially rendering it inoperable.
• Prior to installing your HAB™, please take pictures of the label on the left side,
including the serial number, serial number bar-code, QR code, and MAC
address. Store this information for your records, it is valuable and may be nec-
essary for system configuration or troubleshooting. Depending on your HAB™
unit’s position, viewing this information after installation may be dif
ficult.
• It may be easier to open the tabs at the bottom (along the sides) of the box and
remove the box from the pallet, rather than removing the top lid and lifting the
HAB™ with the handles.
3
5
6
•
Turn O
n the HAB™ befor
e remo
ving from cr
ate.
•
Turn on unit b
y holding the po
wer
button f
or 3-5 sec
onds.
•
(Hold un
til gr
een RUN LED flashes)
•
Turn O
n the invert
ers main DC input disconnect Br
eaker
.
•
Turn O
n the HAB™ DC Break
er.
•
Turn O
n the HAB™ using Pow
er butt
on , Press and hold f
or
3-5 seconds un
til the GREEN RUN LED flashes.
HAB™
QUICK S
TAR
T GUIDE
330 Codman Hill Road, Boxborough, MA 01719 | +1(888)218–5924 | [email protected] | www
.kilovault.com
4
•
With the ba
ttery
break
er o
ff, and HAB™ po
wer
Off (U
sing the
Pow
er butt
on
)
•
Connect proper
DC cabling to the t
erminals of the HAB™
•
Ensur
e all terminals bolts ar
e tor
qued to specs.
1
•
While the HAB™ is still in its cr
ate, R
egister
the KiloVault HAB™
•
Download the Kilo
Vault HAB iT
app and Activ
ate the HAB™ on
the Cloud.
2
•
Aft
er the c
ommunication cables ar
e connect
ed.
•
Set the HAB™ addr
ess using the address DIP
swit
ch
NOTE
Ref
er to 4.6.
7 Setting the HAB™
Addr
ess, of HAB U
sers Manual.
NOTE
Failur
e to activ
ate the HAB™ on the CL
OUD using the KiloVault iT
app
will v
oid the W
arranty
.
Scan the QR code
with your
mobile devic
e to be r
edirect
ed to the
KiloVault r
egistration page.
NOTE
Refer to 4.6.1. Connecting the HAB™, of Users Manual.
DO NOT reverse the polarity (positive and negative) of your unit’
s connec-
tions. NEVER short circuit your KiloVault® HAB™.
Registration
NOTE
Ref
er to 4.2. U
npacking the KiloVault® HAB™,o
f users M
anual.
Available on the Kilo
Vault
websit
e.
Unboxing
Connecting
the HAB™
Setting the HAB™
Address
Powering Up
the HAB
Mounting and
Securing
the HAB™
•
Using sufficien
t resour
ces lift the HAB™ on
to the
wall
brack
et. U
sing the two M8*16mm bolts pr
ovided, secur
e
the HAB™ to the
wall
brack
et.
•
We str
ongly r
ecommend using lift equipmen
t and straps t
o
secure and st
eady the Kilo
Vault® HAB™.
QuickStartGuide_HAB_edit.indd 1
QuickStartGuide_HAB_edit.indd 1
11/23/22 2:22 PM
11/23/22 2:22 PM
Note:
Read this entire document, in addition to the Installation Manual, before installing
or using the KiloVault HAB™. Failure to do so or to follow any of the instructions
or warnings in this document can result in electrical shock, serious injury, or
death, or can damage the HAB™, potentially rendering it inoperable.
• Prior to installing your HAB™, please take pictures of the label on the left side,
including the serial number, serial number bar-code, QR code, and MAC
address. Store this information for your records, it is valuable and may be nec-
essary for system configuration or troubleshooting. Depending on your HAB™
unit’s position, viewing this information after installation may be dif
ficult.
• It may be easier to open the tabs at the bottom (along the sides) of the box and
remove the box from the pallet, rather than removing the top lid and lifting the
HAB™ with the handles.
3
5
6
•
Turn O
n the HAB™ befor
e remo
ving from cr
ate.
•
Turn on unit b
y holding the po
wer
button f
or 3-5 sec
onds.
•
(Hold un
til gr
een RUN LED flashes)
•
Turn O
n the invert
ers main DC input disconnect Br
eaker
.
•
Turn O
n the HAB™ DC Break
er.
•
Turn O
n the HAB™ using Pow
er butt
on , Press and hold f
or
3-5 seconds un
til the GREEN RUN LED flashes.
HAB™
QUICK S
TAR
T GUIDE
330 Codman Hill Road, Boxborough, MA 01719 | +1(888)218–5924 | [email protected] | www
.kilovault.com
4
•
With the ba
ttery
break
er o
ff, and HAB™ po
wer
Off (U
sing the
Pow
er butt
on
)
•
Connect proper
DC cabling to the t
erminals of the HAB™
•
Ensur
e all terminals bolts ar
e tor
qued to specs.
1
•
While the HAB™ is still in its cr
ate, R
egister
the KiloVault HAB™
•
Download the Kilo
Vault HAB iT
app and Activ
ate the HAB™ on
the Cloud.
2
•
Aft
er the c
ommunication cables ar
e connect
ed.
•
Set the HAB™ addr
ess using the address DIP
swit
ch
NOTE
Ref
er to 4.6.
7 Setting the HAB™
Addr
ess, of HAB U
sers Manual.
NOTE
Failur
e to activ
ate the HAB™ on the CL
OUD using the KiloVault iT
app
will v
oid the W
arranty
.
Scan the QR code
with your
mobile devic
e to be r
edirect
ed to the
KiloVault r
egistration page.
NOTE
Refer to 4.6.1. Connecting the HAB™, of Users Manual.
DO NOT reverse the polarity (positive and negative) of your unit’
s connec-
tions. NEVER short circuit your KiloVault® HAB™.
Registration
NOTE
Ref
er to 4.2. U
npacking the KiloVault® HAB™,o
f users M
anual.
Available on the Kilo
Vault
websit
e.
Unboxing
Connecting
the HAB™
Setting the HAB™
Address
Powering Up
the HAB
Mounting and
Securing
the HAB™
•
Using sufficien
t resour
ces lift the HAB™ on
to the
wall
brack
et. U
sing the two M8*16mm bolts pr
ovided, secur
e
the HAB™ to the
wall
brack
et.
•
We str
ongly r
ecommend using lift equipmen
t and straps t
o
secure and st
eady the Kilo
Vault® HAB™.
QuickStartGuide_HAB_edit.indd 1
QuickStartGuide_HAB_edit.indd 1
11/23/22 2:22 PM
11/23/22 2:22 PM
Note:
Read this entire document, in addition to the Installation Manual, before installing
or using the KiloVault HAB™. Failure to do so or to follow any of the instructions
or warnings in this document can result in electrical shock, serious injury, or
death, or can damage the HAB™, potentially rendering it inoperable.
• Prior to installing your HAB™, please take pictures of the label on the left side,
including the serial number, serial number bar-code, QR code, and MAC
address. Store this information for your records, it is valuable and may be nec-
essary for system configuration or troubleshooting. Depending on your HAB™
unit’s position, viewing this information after installation may be dif
ficult.
• It may be easier to open the tabs at the bottom (along the sides) of the box and
remove the box from the pallet, rather than removing the top lid and lifting the
HAB™ with the handles.
3
5
6
•
Turn O
n the HAB™ befor
e remo
ving from cr
ate.
•
Turn on unit b
y holding the po
wer
button f
or 3-5 sec
onds.
•
(Hold un
til gr
een RUN LED flashes)
•
Turn O
n the invert
ers main DC input disconnect Br
eaker
.
•
Turn O
n the HAB™ DC Break
er.
•
Turn O
n the HAB™ using Pow
er butt
on , Press and hold f
or
3-5 seconds un
til the GREEN RUN LED flashes.
HAB™
QUICK S
TAR
T GUIDE
330 Codman Hill Road, Boxborough, MA 01719 | +1(888)218–5924 | [email protected] | www
.kilovault.com
4
•
With the ba
ttery
break
er o
ff, and HAB™ po
wer
Off (U
sing the
Pow
er butt
on
)
•
Connect proper
DC cabling to the t
erminals of the HAB™
•
Ensur
e all terminals bolts ar
e tor
qued to specs.
1
•
While the HAB™ is still in its cr
ate, R
egister
the KiloVault HAB™
•
Download the Kilo
Vault HAB iT
app and Activ
ate the HAB™ on
the Cloud.
2
•
Aft
er the c
ommunication cables ar
e connect
ed.
•
Set the HAB™ addr
ess using the address DIP
swit
ch
NOTE
Ref
er to 4.6.
7 Setting the HAB™
Addr
ess, of HAB U
sers Manual.
NOTE
Failur
e to activ
ate the HAB™ on the CL
OUD using the KiloVault iT
app
will v
oid the W
arranty
.
Scan the QR code
with your
mobile devic
e to be r
edirect
ed to the
KiloVault r
egistration page.
NOTE
Refer to 4.6.1. Connecting the HAB™, of Users Manual.
DO NOT reverse the polarity (positive and negative) of your unit’
s connec-
tions. NEVER short circuit your KiloVault® HAB™.
Registration
NOTE
Ref
er to 4.2. U
npacking the KiloVault® HAB™,o
f users M
anual.
Available on the Kilo
Vault
websit
e.
Unboxing
Connecting
the HAB™
Setting the HAB™
Address
Powering Up
the HAB
Mounting and
Securing
the HAB™
•
Using sufficien
t resour
ces lift the HAB™ on
to the
wall
brack
et. U
sing the two M8*16mm bolts pr
ovided, secur
e
the HAB™ to the
wall
brack
et.
•
We str
ongly r
ecommend using lift equipmen
t and straps t
o
secure and st
eady the Kilo
Vault® HAB™.
QuickStartGuide_HAB_edit.indd 1
QuickStartGuide_HAB_edit.indd 1
11/23/22 2:22 PM
11/23/22 2:22 PM
