Kikusui TOS5300 Скачать руководство пользователя страница 52

Страница: 52 / 77

TOS5300_INTERFACE

SCPI Register Model

PROTecting status register (STATus:OPERation:PROTecting)

The PROTecting status register is a 16-bit register that contains information about the status of the
TOS5300 Series protective features. This status register is unique to the TOS5300 Series.

STAT:OPER:PROT

Queries the event of the PROTecting status register.

A query clears the contents of the register.

Command

STATus:OPERation:PROTecting[:EVENt]?

Response

Returns the event of the PROTecting status register in <NR1> format.

STAT:OPER:PROT:COND

Queries the condition of the PROTecting status register.

A query does not clear the contents of the register.

Command

STATus:OPERation:PROTecting:CONDition?

Response

Returns the condition of the PROTecting status register in <NR1> format.

Bit

Bit weight

Bit name

Description

Interlock (ILOCK)

Interlock signal input detected.

Calibration (CAL)

The set calibration date has passed.

NOT USED

—

NOT USED

—

Power Supply (PS)

Power supply problem detected.

Volt Error (VERR)

The output voltage exceeded the rated limits..

NOT USED

—

128

NOT USED

—

256

Over Load (OL)

The output power exceeded the output limit.

512

Over Heat (OH)

The internal temperature of the TOS5300 Series
has become abnormally high.

1024

Over Rating (OR)

An output current was generated for a length of
time that exceeds the rated time.

2048

NOT USED

—

4096

Remote (RMT)

A connection or disconnection of the remote
control connector was detected.

8192

SIGNAL I/O (SIO)

A change in the SIGNAL I/O connector’s ENABLE
signal was detected.

16384

USB

A connection or disconnection of the USB cable
while the TOS5300 Series was being controlled
remotely was detected.

32768

NOT USED

—

Содержание TOS5300














































































Результаты поиска

Содержание TOS5300

Отзывы:

Kikusui TOS5300, Руководство по интерфейсу связи, Страница: 52 / 77

Результаты поиска

Содержание TOS5300

Отзывы: