Kikusui TOS5300 Скачать руководство пользователя страница 17

Страница: 17 / 77

TOS5300_INTERFACE

IEEE 488.2 Common Commands

*CLS

p. 46

IEEE 488.2-1992, section
10.3

Clears all event registers including the status byte, event status, and error/event queue.

Command

*CLS

*ESE

p. 49

IEEE 488.2-1992, section
10.10

Sets the event status enable register that is counted by the event summary bit (ESB) of the status
byte.

Command

*ESE <NR1>
*ESE?

Parameter

Value:

0 to 255
An SCPI error (-222, “Data out of range”) occurs if the specified value is outside the

range.

Example

When *ESE 16 is transmitted, bit 4 of the event status enable register is set. Each time

the execution error bit (bit 4) of the event status register is set, the summary bit (ESB) of

the status byte is set.

Response

Returns the value of the event status enable register in <NR1> format.

*ESR

p. 49

IEEE 488.2-1992, section
10.12

Queries the event status register. Registers that are read are cleared.

Command

*ESR?

Response

Returns the value of the event status register in <NR1> format and clears the register.

*IDN

IEEE 488.2-1992, section
10.14

Queries the model name, serial number, and firmware version of the TOS5300 Series.

Command

*IDN?

Response

The response to *IDN? is indicated below.

Example

For a TOS5301 with serial number AB123456 and firmware version 1.00, *IDN? returns:

KIKUSUI,TOS5301,AB123456,1.00

See

Содержание TOS5300














































































Результаты поиска

Содержание TOS5300

Отзывы:

Kikusui TOS5300, Руководство по интерфейсу связи, Страница: 17 / 77

Результаты поиска

Содержание TOS5300

Отзывы: