Kikusui PWX1500H Скачать руководство пользователя страница 87 | Manualshive

Страница: 87 / 131

background image

PWX

87

Series Operation

Parallel

/Series Operation

4

Settings (series operation)

Setting the voltage and current

Set the voltage and current on each unit. The voltage that is output is the total of the voltages
of the two units. Set the current to the same value on the two units.

Setting the overvoltage protection (OVP) and overcurrent protec-
tion (OCP)

In series operation, you have to set the overvoltage protection (OVP) and overcurrent protec-
tion (OCP) on both units. Specify the same values on the two units.

Starting series operation

Turning the power on and off

Turn the POWER switch on unit 1 and unit 2 on or off.

Turning the output on and off

Press OUTPUT on unit 1 and unit 2 to turn the output on or off.

See

CAUTION

After you turn the POWER switch off, wait at least 10 seconds after the fan stops before you
turn the POWER switch back on. Repeatedly turning the POWER switch on and off at short
intervals can cause damage to the inrush current limiter. In turn, this will shorten the service
life of the POWER switch, internal input fuse, and other components.

«
...
85
86
87
88
89
...
»

Содержание PWX1500H




































































































































Отзывы:

Нет отзывов

Похожие инструкции для PWX1500H

Бренд: Makita Страницы: 60

Бренд: Narex Страницы: 32

Бренд: National Instruments Страницы: 8

Бренд: Palmgren Страницы: 20

FLIEGUAN-HANDY FXH-25

Бренд: probst Страницы: 76

Бренд: King Industrial Страницы: 7

Бренд: MULTIQUIP Страницы: 60

Бренд: SW-Stahl Страницы: 12

Бренд: Kärcher Страницы: 68

Бренд: Dixon Automatic Tool Страницы: 11

Бренд: Far Tools Страницы: 52

Бренд: Jarvis Страницы: 12

Бренд: Bomag Страницы: 58

Бренд: Xinpu Страницы: 13

Бренд: Zipper Mowers Страницы: 43

Бренд: Surtek Страницы: 16

Бренд: Panamax Страницы: 45

Бренд: Kolver Страницы: 3

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды