Kikusui PLZ1004WH, Руководство пользователя

Страница: 134 / 158

134
PLZ-4WH
Specifications
Common specifications
Analog External Control (EXT CONT connector)
Load on/off control input Turn on the load with a high (or low) CMOS level signal
Logic level switchable.
The internal circuit is pulled up to 5 V by a 10 k
Ω
resistor.
Range switch input Switch ranges L, M, and H using a 2-bit signal
Trigger input Clear the sequence operation pause with a high CMOS level signal whose
duration is 10 µs or longer
The internal circuit is pulled down to common by a 100 k
Ω
resistor.
External alarm input Activate the alarm with a low CMOS level signal
The internal circuit is pulled up to 5 V by a 10 k
Ω
resistor.
Alarm status output On when OVP, OCP, OPP, OHP, or REV is activated or when an external
alarm input is applied (open collector output from a photocoupler)
Load on status output On when the load is on (open collector output from a photocoupler)
Range status output Outputs range L, M, or H using a 2-bit signal (open collector output from a
photocoupler).
Short signal output Relay contact output (30 Vdc/1 A).
External voltage control
(CC, CR, CP, and CV
mode) External input voltages in the range of 0 V to 10 V correspond to 0 % to
100 % of the rated current (CC mode), rated power (CP mode), and rated
voltage (CV mode).
External input voltages in the range of 0 V to 10 V correspond to the range
of resistances from the maximum resistance to the minimum resistance
(CR mode).
External resistance control
(CC, CR, CP, and CV
mode) External resistances in the range of 0
Ω
to 10 k
Ω
correspond to 0 % to 100
% or 100 % to 0 % of the rated current (CC mode), rated power (CP
mode), or rated voltage (CV mode).
External resistances in the range of 0
Ω
to 10 k
Ω
correspond to the range
of resistances from the maximum resistance to the minimum resistance or
from the minimum resistance to the maximum resistance (CR mode).
Current monitor output 10 V for f.s (H or L range), 1 V for f.s (M range)
Voltage monitor output For each range, 10 V for f.s
Front-Panel BNC Terminal
TRIG OUT Transmits pulses during sequence operation and switching operation.
Output impedance: 1 k
Ω
, Output voltage: approx. 4.5 V, Pulse width: 2 µs
Current monitor output 10 V for f.s (H or L range), 1 V for f.s (M range)
Output current: up to 5 mA
Voltage monitor output For each range, 6.5 V for f.s, Output current: up to 5 mA
Communication Functions
GPIB IEEE std. 488.1-1987
SH1, AH1, T6, L4, SR1, RL1, PP0, DC1, DT1, C0, E1
Supports the SCPI and IEEE std. 488.2-1992 command set
Sets panel functions except for the function of the power switch and reads
measured values
RS232C D-SUB 9-pin connector (conforms to EIA-232-D)
Supports the SCPI and IEEE std. 488.2-1992 command set
Sets panel functions except for the function of the power switch and reads
measured values
Baud rate: 2400, 4800, 9600, 19200 bps
Data length: 8 bits, Stop bits: 1/2 bits, Parity bit: None
Flow control: Xon/Xoff
USB Conforms to the USB 2.0 specifications and the USBTMC-USB488 device
class specifications
Sets panel functions except for the function of the power switch and reads
measured values
Communication speed 12 Mbps (Full speed)