Kikusui PFX2532 Скачать руководство пользователя

Страница: 38 / 142

PFX2532

Connecting to the Electronic Load

Connecting the electronic load control cable

Attach the lock lever to the I/F cable SC05-PFX for PLZ-5W.

Attach it to the connector on the side with the ferrite core.
If the lock lever is not attached, the connector may come off.

Check that all devices that you will connect are turned off.

Insert the I/F cable SC05-PFX for PLZ-5W to the "DC ELECTRONIC LOAD"
connector on the rear panel of PFX2532.

Insert the end with a ferrite core into the PFX2532.
Confirm that the lock lever is pulled down and it is firmly connected.

Insert the other end of the I/F cable SC05-PFX for PLZ-5W to the "EXT CONT"
connector on the PLZ-5W.

Insert it securely, and check that it does not fall out.

Lock lever

I/F cable for PLZ-5W

PFX2532

Lock lever

Ferrite core

Содержание PFX2532















































































































































Результаты поиска

Содержание PFX2532

Отзывы:

Похожие инструкции для PFX2532

Бренды по названию

Популярные бренды

Kikusui PFX2532, Руководство по эксплуатации

Результаты поиска

Содержание PFX2532

Отзывы:

Похожие инструкции для PFX2532

Бренды по названию

Популярные бренды