Kikusui PFX2532 Скачать руководство пользователя | Manualshive

Страница: 21 / 142

background image

PFX2532

21

Combination for Performing Charge/Discharge Tests

1

Des

cr

iption

The graph below shows the range of dischargeable voltage and current using the following
equation. Use devices whose voltage (discharge start voltage, cutoff voltage) and current (constant
current) do not exceed the range. Also, make sure that the discharge voltage does not fall below
the minimum discharge operating voltage.

When using constant power discharge (CP Dish), calculate the discharge current from the specified
constant power value and DUT (battery) voltage, and check that it is within the range on the graph.

Minimum discharge operating voltage

1

= Minimum operating voltage of the electronic load +

voltage drop due to loss in cables

If you want to perform discharge tests with a voltage lower than the minimum discharge operating
voltage, use a bias power supply in combination.

1

What is minimum discharge operating voltage?
It is a voltage based on the minimum operating voltage of the electronic load. The minimum
discharge operating voltage is this minimum operating voltage with the loss in cable (voltage
drop) added.

See

If the allowable power of electronic loads is exceeded during discharging or the voltage falls below
the minimum discharge operating voltage, a CD / B alarm or the like occurs, and the test is
aborted.

Voltage (V) axis

Discharge start voltage

value (Start voltage) or cutoff voltage value (Cutoff voltage)

Current (A) axis

Constant current

value (CC Current)

0

20

40

60

80

100

120

140

160

180

200

70

60

50

40

30

20

10

0

Current (A)

Voltage (V)

Discharge operating range of each electronic Load

［

PLZ-4W

］

DUT cable: At nominal cross-sectional area 80 mm

2

3 m

PFX2532 operating range

P2004WB

PLZ1004W
+2004WB x2

PLZ minimum
operating voltage

«
...
19
20
21
22
23
...
»

Содержание PFX2532















































































































































Отзывы:

Нет отзывов

Похожие инструкции для PFX2532

Бренд: HANYOUNG NUX Страницы: 56

Бренд: Jabra Страницы: 3

Бренд: Talgil Страницы: 14

Бренд: Tadao Страницы: 2

Бренд: Eaton Страницы: 96

Бренд: GADGETMONSTER Страницы: 30

Бренд: Penn Страницы: 10

Бренд: Simplex Страницы: 40

U-verse Advance Series A10

Бренд: AT&T Страницы: 2

Бренд: Goodson Страницы: 4

Бренд: Moeller Страницы: 2

Бренд: SMC Networks Страницы: 15

Бренд: National Instruments Страницы: 22

Бренд: Stramatel Страницы: 10

Бренд: Vector Страницы: 10

Бренд: Ebyte Страницы: 20

EG-PWC-PSWRC-01

Бренд: Energenie Страницы: 2

ZigBee Pro VT8000 Series

Бренд: Viconics Страницы: 3

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды