Kikusui LIN Series Скачать руководство пользователя

Страница: 59 / 74

LIN-JF

Specifications

This chapter lists the electrical and mechanical specifications of the product.

Item

LIN1020JF

LIN3020JF

OP01-LIN1020JF

Compliant standards

JIS C61000-3-2(2011), JETGR0003-1-2.0(2011), JIS C8962(2008),
IEC 61000-3-3(2008)

Reference
impedance

Supported wiring systems

Single-phase two-wire
(Single-phase three-
wire, three-phase
three-wire, and three-
phase four-wire are
supported with the
OP01-LIN1020JF
option.)

Single-phase two-
wire, single-phase
three-wire, three-
phase three-wire, and
three-phase four-wire

Single-phase three-
wire, three-phase
three-wire, and three-
phase four-wire (in
combination with the
LIN1020JF)

Impedance
value

U, V, and W
phases

Z1, Z2: 0.19

Ω

+ 0.23 mH, Z3: 0.24

Ω

+ jn 0.15

Ω

Phase impedance bypassing is possible.

N phase

Z1: 0.21

Ω

+ 0.14 mH, Z2: 0.19

Ω

+ 0.23 mH,

Z3: 0.16

Ω

+ jn 0.10

Ω

Impedance bypassing is possible.

Impedance
error

Resistance

± 5 %

Reactance

± 5 % (50 Hz/60 Hz), ± 15 % (reference value at 1 kHz),
± 20 % (reference value at 3 kHz)

Residual
resistance
during bypass

Each phase

10 m

Ω

or less

Maximum
rated voltage

Phase voltage 300 Vrms
Line voltage

500 Vrms

Maximum
rated current

Each phase

20 Arms (continuous)

Rated frequency

50 Hz/ 60 Hz (Z1, Z2), 50 Hz (Z3)

Input and output terminals

Terminal block, M6 screws

Control
features

Voltage sensing

Supports the hardware sensing functions of the PCR-LE and PCR-
LE2 series using the internal sensing points of each phase

Terminal

L-N phase
Terminal block, M3
screws

U-N, V-N, and W-N
phases
Terminal block, M3
screws

V and W phases
Terminal block, M3
screws

Contact signal control

Impedance selection using contact signals

Not available

Operation
current

Approx. 100 mAdc (24 Vdc open voltage or
less) per circuit; internal relay operates
through current absorption by the open-col-
lector circuit

Status output

Status output using contact signals

Not available

Contact
rating

5 Adc, 35 Vdc
Contact connected to the internal circuit com-
mon when shorted

USB remote control

Impedance selection and status querying
using an isolated digital I/O terminal

Not available

Controller

DIO0808LY-USB by CONTEC
Complies with USB2.0 HighSpeed(480Mbps)
and USB1.1

USB port

Type B

PCR control

Turns off AC power supply output when over-
heating protection is activated

Not available

Output
terminal

Mini-Din6P female

Содержание LIN Series











































































Результаты поиска

Содержание LIN Series

Отзывы:

Похожие инструкции для LIN Series

Бренды по названию

Популярные бренды

Kikusui LIN Series, Руководство по эксплуатации

Результаты поиска

Содержание LIN Series

Отзывы:

Похожие инструкции для LIN Series

Бренды по названию

Популярные бренды