Kikusui KHA3000 Скачать руководство пользователя страница 79 | Manualshive

Страница: 79 / 392

Kikusui KHA3000 Скачать руководство пользователя страница 79

4

KHA3000

79

Switching Displays

System

Setup

Keys Used to Switch between the Three Basic Views

As explained above, the harmonic current testing display and voltage fluctuation testing
display each has three basic views. In the harmonic current testing display, use the HA key
and VIEW key to change views. In the voltage fluctuation testing display, use the Vf key and
VIEW key to change views.

Harmonic current testing display

•

Press the HA key to display the HA-Test Conditions List display (the HA key LED
illuminates.)

•

Pressing the VIEW key while the HA key

’

s LED is lit displays the HA-Observation and

Analysis display (HA-VIEW). Under this condition, the HA-Observation and Test
Conditions display and HA-Observation and Analysis display (HA-VIEW) are displayed
alternately each time the VIEW key is pressed.

•

Pressing the HA key displays the HA-Test Conditions List display again.

Voltage fluctuation testing display

•

Press the Vf key to display the Vf-Test Conditions List display (the Vf key LED
illuminates).

•

Pressing the VIEW key while the Vf key

’

s LED is lit displays the Vf-Observation and

Analysis display (Vf-VIEW). Under this condition, the Vf-Observation and Test
Conditions display and Vf-Observation and Analysis display (Vf-VIEW) are displayed
alternately each time the VIEW key is pressed.

•

Pressing the Vf key displays the Vf-Test Conditions List display again.

HA-Test Conditions

List display

HA-Observation and

Test Conditions display

HA-Observation and

Analysis display

(HA-VIEW)

VIEW key

VIEW key

VIEW key

HA key

LED of HA key

illuminates

Harmonic current test

LED of VIEW key

illuminates

LED of VIEW key

is turned off

Vf-Test Conditions

List display

Vf-Observation and

Test Conditions display

Vf-Observation and

Analysis display

(Vf-VIEW)

VIEW key

VIEW key

VIEW key

Vf key

LED of Vf key

illuminates

Voltage fluctunation test

LED of VIEW key

is turned off

LED of VIEW key

illuminates

«
...
77
78
79
80
81
...
»

Содержание KHA3000









































































































































































































































































































































































































Отзывы:

Нет отзывов