Kikusui KHA3000 Скачать руководство пользователя страница 74 | Manualshive

Страница: 74 / 392

Kikusui KHA3000 Скачать руководство пользователя страница 74

74

KHA3000

Power-On of the Test System

This section explains how to turn on the power to the test system including this product, the
AC Power Supply and Line Impedance Network. There are the following two methods for
turning on/off the power switch:

●

Separate ON/OFF

Turn on and off the POWER switches of individual devices separately.

●

Collective ON/OFF

Turn on and off the power collectively using an external power switch. Lock the POWER
switches of individual devices in the ON position. The customer is requested to prepare
the external power switch.

Separate ON/OFF

This method is normally used to control the AC Power Supply from this product. This
procedure is explained below.
To prevent damage to the internal relay contact of the Line Impedance Network, follow the
procedure exactly. For details on preventing damage to the internal relay contact, refer to the
Operation Manual of the Line Impedance Network.

Turning on the POWER switch

1

Turn on the POWER switch of the Line Impedance Network.

2

Turn on the POWER switch of the AC Power Supply.

The version is displayed for several seconds on the control panel of the AC Power
Supply. The output remains at OFF. For details on the version display, refer to the
Operation Manual of the AC Power Supply.
Subsequent operations are controlled from this product, KHA3000.

3

Turn on the POWER switch of this product.

Press the POWER switch ( ). With the startup sound, all LEDs illuminate and the
firmware version is displayed.

«
...
72
73
74
75
76
...
»

Содержание KHA3000









































































































































































































































































































































































































Отзывы:

Нет отзывов