Kikusui KHA3000 Скачать руководство пользователя страница 60 | Manualshive

Страница: 60 / 392

Kikusui KHA3000 Скачать руководство пользователя страница 60

60

KHA3000

Using CT (current transformer)

When the current of the device to be measured exceeds the maximum current range of this
product,  a  CT  (current  transformer)  may  be  connected.  Here,  the  connections  for  single-
phase  two-wire  (1P2W),  single-phase  three-wire  (1P3W),  three-phase  three-wire  (3P3W),
and three-phase four-wire (3P4W) systems are described. The impedance shown is used in
the  flicker  tests.  Except  for  some  special  cases,  the  impedance  will  not  be  used  in  the
harmonic current tests.
The voltmeter is for the connection to external measurement points.
L1, L2, and L3 are the three input phases (channels). L1 will be the reference phase for the
measurement. Be sure to connect L1.

Circuit diagram

Single-phase two-wire (1P2W) circuit

Single-phase three-wire (1P3W) circuit

WARNING

•

This work has a risk of electric shock. For the AC power supply used for the
measurement circuit, be sure to disconnect the power cord from the outlet, turn off
the switch on the switchboard to which the power cord is connected, and turn off the
POWER switch.

CAUTION

Terminal G of this product is not a protective conductor terminal. It is not grounded even if
the wire is connected to terminal G. For terminals G and N, the respective SOURCE and
LOAD terminals are short-circuited internally.

CT

A

V

L1

N

G

V

SOURCE

LOAD

KHA3000

EXT INPUT

L

N

G

L

N

G

AC power

supply

Impedance

network

EUT

CT

A

V

L1

V

SOURCE

LOAD

KHA3000

EXT INPUT

A

V

L2

N

G

V

EXT INPUT

L1

L2

N

G

L1

L2

N

G

AC power

supply

Impedance

network

EUT

«
...
58
59
60
61
62
...
»

Содержание KHA3000









































































































































































































































































































































































































Отзывы:

Нет отзывов