manualshive.com logo in svg

Kikusui KHA3000, Руководство по эксплуатации, Страница: 380 / 392

Поделиться
Скачать
Kikusui KHA3000 Скачать руководство пользователя страница 380

380

KHA3000

E

Report Printing Format

A report printing format is provided for each limit value standard. The format varies depending
on the combination of test conditions.

�

Combination of test conditions

•

Limit value standard (IEC, JIS)

IEC 61000-3-2 Ed5.0(2018)
IEC 61000-3-2 Ed3.0(2005)
IEC 61000-3-2 Ed2.2(2004)
IEC 61000-3-12 Ed1.0(2004)
JIS C61000-3-2(2019)
JIS C61000-3-2(2005)
IEC 61000-3-3 Ed3.1(2017)
IEC 61000-3-11 Ed2.0(2017)

•

Measurement circuit type

Single-phase two-wire
Single-phase three-wire
Three-phase three-wire
Three-phase four-wire

•

Measurement method for the voltage fluctuation test

Pst Auto
Manual

Examples of representative printing formats are provided on the following pages.

•

IEC 61000-3-2 Ed2.2(2004), single-phase two-wire

•

IEC 61000-3-3 Ed3.1(2017), single-phase two-wire, Pst Auto

Содержание KHA3000









































































































































































































































































































































































































Отзывы:

Нет отзывов