Kikusui KHA3000 Скачать руководство пользователя страница 334

Страница: 334 / 392

334

KHA3000

System Setting

Buzzer

SYST:BEEP:VOL

Sets the buzzer volume.

Command

SYSTem:BEEPer:VOLume {<numeric>|MIN|MAX}

SYSTem:BEEPer:VOLume?

Parameter Value:

0 to 8

Unit:

None

Response

Returns the buzzer volume in the <NR3> format.

Setting the Date and Time

SYST:DATE

Sets the date.

Command

SYSTem:DATE <YEAR_NR1>,<MONTH_NR1>,<DAY_NR1>

SYSTem:DATE?

Parameter <YEAR_NR1> Year

Value:

2000 to 2099

<MONTH_NR1> Month
Value:

1 to 12

<DAY_NR1> Day
Value:

1 to 31

Response

Returns year, month and day in this order in the <NR1>, <NR1>, <NR1> format.

SYST:TIME

Sets the time.

Command

SYSTem:TIME <HOUR_NR1>,<MIN_NR1>,<SEC_NR1>

SYSTem:TIME?

Parameter <HOUR_NR1> Hour

Value:

0 to 23

<MIN_NR1> Minute, <SEC_NR1> Second
Value:

0 to 59

Response

Returns hour, minute and second in this order in the <NR1>, <NR1>, <NR1> format.

Содержание KHA3000









































































































































































































































































































































































































Результаты поиска

Содержание KHA3000

Отзывы:

Kikusui KHA3000, Руководство по эксплуатации, Страница: 334 / 392

Результаты поиска

Содержание KHA3000

Отзывы: