Kikusui KHA3000 Скачать руководство пользователя страница 331

Страница: 331 / 392

KHA3000

331

Querying Measurement Data

Rem

ote Contr

MEASure[<channel#>][:SCALar]:POWer:AC:PFACtor?

Response

Returns the power factor in the <NR3> format.

Querying Voltage

FETC:VOLT:AC

READ:VOLT:AC

MEAS:VOLT:AC

Each queries the measured value of the AC voltage (effective value).

Command

FETCh[<channel#>][:SCALar]:VOLTage:AC?

READ[<channel#>][:SCALar]:VOLTage:AC?

MEASure[<channel#>][:SCALar]:VOLTage:AC?

Response

Returns the measured value of the AC voltage (rms) in the <NR3> format.
Unit:

FETC:VOLT:AMPL:MAX

READ:VOLT:AMPL:MAX

MEAS:VOLT:AMPL:MAX

Each queries the measured value of the maximum voltage (positive amplitude peak value).

Command

FETCh[<channel#>][:SCALar]:VOLTage:AMPLitude:MAXimum?

READ[<channel#>][:SCALar]:VOLTage:AMPLitude:MAXimum?

MEASure[<channel#>][:SCALar]:VOLTage:AMPLitude:MAXimum?

Response

Returns the measured value of the maximum voltage (positive amplitude peak value) in the
<NR3> format.
Unit:

FETC:VOLT:AMPL:MIN

READ:VOLT:AMPL:MIN

MEAS:VOLT:AMPL:MIN

Each queries the measured value of the minimum voltage (negative amplitude peak value).

Command

FETCh[<channel#>][:SCALar]:VOLTage:AMPLitude:MINimum?

READ[<channel#>][:SCALar]:VOLTage:AMPLitude:MINimum?

MEASure[<channel#>][:SCALar]:VOLTage:AMPLitude:MINimum?

Response

Returns the measured value of the minimum voltage (negative amplitude peak value) in the
<NR3> format.
Unit:

Содержание KHA3000









































































































































































































































































































































































































Результаты поиска

Содержание KHA3000

Отзывы:

Kikusui KHA3000, Руководство по эксплуатации, Страница: 331 / 392

Результаты поиска

Содержание KHA3000

Отзывы: